Jeep Wrangler Forum banner

Bed liner on stock wheels.

121K views 182 replies 58 participants last post by  m.elliott63 
#1 ·
Howdy,
I have been contemplating this for some time now and I finally did it today, painting my stock wheels with Bed liner.
Initially I was just going to paint the windows on the wheels and leave the face silver. This did not work so well, but I will include the pics anyway.

First, go to the store and buy 2 cans of rustoleum truck bed liner. Be sure that you do not grab 1 can of bed liner and 1 can of undercoating. Stupid walmart people put them both in the same row. guess I should have verified I got the right thing, though.


Second, pull the spare off the jeep and bring it into your shop/garage/workspace.

Yes, the sheets have poka-dots on them. No, they are not my sheets. They are my girlfriend's sheets.


Third, Mask off the edges of the face and window area if you are going to paint the windows, so you don't sand the face.


Fourth, Sand the area to be painted, whether it be the whole wheel or the windows only. I used 200 grit sandpaper so it was not too smooth, but not too rough.



Fifth, Clean off the dust with some alcohol and a rag.

Sixth, if you are painting the windows, cover the opening with paper/tape.


Seventh, paint from the inside of the wheel, try to get in the corners as much as possible. Then let it dry for about 20 minutes. Peel off the tape/paper and then decide you should have just painted the whole wheel all along. At this time also realize that you sprayed with undercoating, not bed liner.


Eighth, take the wheel, or another one, back inside and remove the center cap and wheel weight. Save these and mark their location with a little bit of paint of a sharpie. The weights can be popped off gently, but it takes some time. I took a wide standard screwdriver to the open point on the clip of the weight and pried them off. The cap just pushes out from behind.

Ninth, sand the whole entire surface of the wheel, including windows, and clean again.

Tenth, I placed small strips of masking tape around the wheel, right where the rubber meets the rim of the wheel to keep the tire from getting sprayed and them taped huge index cards to make the masked area larger, couldn't figure out how to do the "index card trick".


Eleventh, Begin spraying with the bed liner. I sprayed around the rim first, then did the windows, then the face areas. I found this worked the best. You need not do a very thick coat, and don't worry if it has a glossy finish in some areas because it will even out as it dries. Make sure to spray from over a foot away. Let the wheel dry for about 30 minutes.


Twelfth, While that wheel is drying, start on another a wheel.

Thirteenth, Touch up any areas on the wheel that need more bed liner on them.
 
See less See more
8
#43 ·
chrisb0108 said:
I photo shopped this cuz I've been considering painting my aluminum wheels back too. Mine are currently polished aluminum...not very polished at the moment though! :D

If anyone has any aluminum that they painted black I'd like to see them...
Yeah idk if I shld or not I don't want to regret doing it! I was thinking about doing them a charcoal but idk
 
#52 ·
DonC72 said:
I have an open weekend, sold my phillies tix so I might do it this weekend, as long as I can find my damn jack.
Yeah, its pretty easy once you get it going. I wouldn't put primer on first though because from I understand the bedliner has an acid in it that etches the metal. My uncle has a shop that does spray in bedliners, exhaust etc and that is what he told me. Not sure if that only applies to his commercial stuff or all of it (quality brands)
 
#54 ·
I've been a partial season ticket holder since that place opened, and to be honest, nothing beats a fridge full of good beer and food when I want it. ;0

Why not recoup some before vacation and more importantly, spend some quality time with my Jeep. HAHA.
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top