Another Herculiner Sucess - Jeep Wrangler Forum
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Tech Forums > General Jeep Discussion

Join Wrangler Forum Today


Reply
 
Thread Tools

Please support our sponsors and let them know you heard about them on WranglerForum.com
Old 10-04-2009, 11:12 PM   #1
Jeeper
 
dnbearcat's Avatar
 
Join Date: Aug 2009
Location: Columbus, Ohio
Posts: 54
Another Herculiner Sucess

I started on this project based off all the feedback from the people on this forum who have done this. So i thought Id show you my attempt. My wheel wells were in great shape so i left those and will just throw some wax to it to protect them over time. Plus i think the black and tan are kinda cool together. It took me 2 days to do in total. 1 day to prep and the other to apply/dry/apply (2 coats). And tomorrow I will touch up whatever didn't get hit.

What I bought:
1 gallon herculiner kit (advance auto $50), rough steel wool (lowes paint section $5), Acetone ($6), Cheap wire brushes for the little bit of rust around my drain holes.

Scrub well with steel wool. Use wire brushes to remove any dirt of whatnot from the welds and other tight spots. Clean well with acetone. Take your time taping seams and lines. The more single pieces of tape the better (stuff can creep in the seams of the 2 pieces of tape. Then apply and let dry.

CAUTIONS!
i have a 1999 jeep and has little rust, but when removing the rear seat brackets i did have 3 bolts break off on me and couldnt get them out for the life of me, finally had to drill them all the way out and will have to retap the holes. this hung me up for an extra 3 hrs. (pictured below)
Wear gloves! i failed to do so the first coat and spent 20 min scrubbing my hands with acetone. The smell is pretty rough so do use a ventilated area and if at all possible let it set for a few days (top off or windows and doors open) to let it air out and set up properly.

Have extra for touch ups when your done. Use acetone and Q-Tips and an old rag to clean up any spots after final application. I waited about 1.5hrs after i put the last coat down to remove the masking tape (do not use painters tape, use regular masking). It was still pretty tacky so be careful but this will allow you to use the acetone and tips to clean up before it hardens.

I think the final product is nice and would recommend!

P.S.
I posted a while ago about the seat extenders, i didn't install them due to wanting this first, so when i reinstall the seats i will picture and post the seat extender results.
Attached Thumbnails
Click image for larger version

Name:	IMG_0687.jpg
Views:	7
Size:	58.0 KB
ID:	11707   Click image for larger version

Name:	IMG_0688.jpg
Views:	6
Size:	39.8 KB
ID:	11708  

Click image for larger version

Name:	IMG_0690.jpg
Views:	6
Size:	38.4 KB
ID:	11709   Click image for larger version

Name:	IMG_0695.jpg
Views:	11
Size:	68.9 KB
ID:	11710  

Click image for larger version

Name:	IMG_0697.jpg
Views:	11
Size:	99.6 KB
ID:	11711  

dnbearcat is offline   Quote Quick Reply
Old 10-04-2009, 11:28 PM   #2
Jeeper
 
Levinoss's Avatar
 
Join Date: Apr 2007
Location: Jeffersontown
Posts: 5,540
Looks great!

__________________

"Yesterday is history, tomorrow is a mystery, but today is a gift. That is why it is called the "present."
Levinoss is offline   Quote Quick Reply
Old 10-04-2009, 11:36 PM   #3
Aka Vaultzz

WF Supporting Member
 
Vaultzz's Avatar
 
Join Date: Jul 2009
Location: My Secret Lab
Posts: 5,624
It looks more bumpy than mine does... I want yours its better!
__________________
The YJ is in Rebuild Mode
Vaultzz is offline   Quote Quick Reply
Old 10-05-2009, 07:21 AM   #4
that's what she said

WF Supporting Member
 
jgano23's Avatar
 
Join Date: Oct 2008
Location: \m/-_-\m/
Posts: 16,482
Send a message via AIM to jgano23 Send a message via Yahoo to jgano23
looks awesome. i think you'll soon agree that herculining the interior was one of the best things you can do to your jeep.
jgano23 is offline   Quote Quick Reply
Old 10-05-2009, 08:15 AM   #5
Jeeper
 
05GT-O.C.D.'s Avatar
 
Join Date: Sep 2008
Posts: 1,415
+1. Nice job, looks great.

Regarding the tape - I used the painters tape and had NO issues with it. Another forum member used masking tape and it didn't work so well for him as there was penetration beyond the tape. Since I do reccommend the painters tape and you don't, I'm curious as to why.?
__________________
When my time comes, mix my ashes with gunpowder encased in brass, point me towards murderer's and pedophile's and let me fly.

(: ˇ ɹǝʌo ǝɯ 11oɹ ...sıɥʇ pɐǝɹ uɐɔ noʎ ɟı
05GT-O.C.D. is offline   Quote Quick Reply
Old 10-05-2009, 09:18 AM   #6
Jeeper
 
adkjoe's Avatar
 
Join Date: Aug 2009
Location: Northern Vermont
Posts: 1,615
That looks great!!

I have been wanting to do this for a while, ever since my carpet got wet and now smells like mildew....

My jeeps not paid for yet though and even though I'm rough on her I haven't got the courage yet to line the inside, I want to so bad though. I'm jealous.
adkjoe is offline   Quote Quick Reply
Old 10-05-2009, 09:25 AM   #7
Jeeper
 
mrcarcrazy's Avatar
 
Join Date: Jul 2009
Location: Midland/Odessa, TX
Posts: 3,410
Looks great. But I too am curious as to why you suggest against painters tape.
mrcarcrazy is online now   Quote Quick Reply
Old 10-05-2009, 10:41 AM   #8
Jeeper
 
dnbearcat's Avatar
 
Join Date: Aug 2009
Location: Columbus, Ohio
Posts: 54
I guess i shouldn't have been so against it, could have just been a bad brand of painters tape. It wasn't the usual blue kind, but the brand i tried (can't recall name) didn't want to stick well to the metal. Overall i think i was just jaded by the cheaper kind. Since they are so cheap i say try one and if it adheres good, go for it.

Has anyone else had any problems with the bolts on the rear seat brackets?
dnbearcat is offline   Quote Quick Reply
Old 10-05-2009, 11:49 AM   #9
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
You just convinced me to do it
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-05-2009, 12:15 PM   #10
Jeeper
 
05GT-O.C.D.'s Avatar
 
Join Date: Sep 2008
Posts: 1,415
I had no problems on my 98. The backseats were easy. The front seat rear bolts were a little more difficult due to the fact that they're in a position for more water (rust) exposure. Still, none broken. Sorry 'bout the difficulties.
__________________
When my time comes, mix my ashes with gunpowder encased in brass, point me towards murderer's and pedophile's and let me fly.

(: ˇ ɹǝʌo ǝɯ 11oɹ ...sıɥʇ pɐǝɹ uɐɔ noʎ ɟı
05GT-O.C.D. is offline   Quote Quick Reply
Old 10-05-2009, 10:27 PM   #11
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Took out my backseat today, I also broke 3 bolts

Must be pretty common lol
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-05-2009, 10:35 PM   #12
Jeeper
 
dnbearcat's Avatar
 
Join Date: Aug 2009
Location: Columbus, Ohio
Posts: 54
broke 3 bolts too huh, thats kinda funny in a sad coincidental way. wonder why they are doing that, my underside is virtually rust free and they didnt appear to be that bad. Maybe weak bolts in the 99s or bad threads.
dnbearcat is offline   Quote Quick Reply
Old 10-05-2009, 11:33 PM   #13
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Quote:
Originally Posted by dnbearcat View Post
broke 3 bolts too huh, thats kinda funny in a sad coincidental way. wonder why they are doing that, my underside is virtually rust free and they didnt appear to be that bad. Maybe weak bolts in the 99s or bad threads.
Lol exactly, as far as I can tell, its completely rust free underneath. When you drilled out the bolts were you able to salvage the threads to put new bolts in? Or did you just drill it out and put a nut underneath?
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-06-2009, 11:03 AM   #14
Jeeper
 
fishinVA's Avatar
 
Join Date: Jul 2009
Location: Richmond, VA
Posts: 18
That looks awesome! I'm thinking about doing that to my wrangler. My carpet went a long time ago, and although I don't have any rust on my floorboards yet, there's some exposed metal that I'm worried about.

Do you have any issues with the liner getting really hot, since the insulation underneath the front carpet is gone?
fishinVA is offline   Quote Quick Reply
Old 10-06-2009, 11:25 AM   #15
Jeeper
 
05GT-O.C.D.'s Avatar
 
Join Date: Sep 2008
Posts: 1,415
Quote:
Originally Posted by fishinVA View Post
That looks awesome! I'm thinking about doing that to my wrangler. My carpet went a long time ago, and although I don't have any rust on my floorboards yet, there's some exposed metal that I'm worried about.

Do you have any issues with the liner getting really hot, since the insulation underneath the front carpet is gone?
It seems less warm than the paint.
__________________
When my time comes, mix my ashes with gunpowder encased in brass, point me towards murderer's and pedophile's and let me fly.

(: ˇ ɹǝʌo ǝɯ 11oɹ ...sıɥʇ pɐǝɹ uɐɔ noʎ ɟı
05GT-O.C.D. is offline   Quote Quick Reply
Old 10-06-2009, 05:24 PM   #16
Jeeper
 
dnbearcat's Avatar
 
Join Date: Aug 2009
Location: Columbus, Ohio
Posts: 54
I dont think there will be any issues with the heat, i drove without carpet for a while and the bare metal didnt get 'hot' just warm, makes for good foot warmers.I just did my liner on saturday, and its my secondary vehicle so im letting it cure up for a week before i put the seats back in.

I just drilled the bolts all the way through and will retap with new threads or do the bolt and nut idea. One problem with that is the factory nut is welded on there and would be pretty hard to remove. If it doesnt come off the bolt will just have to be longer and itll be a nut tightened to a nut. Not ideal but i guess it is welded on there. Ill probably work on it this weekend so I will keep you posted on what i do.
dnbearcat is offline   Quote Quick Reply
Old 10-06-2009, 07:23 PM   #17
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Just Hurculined my Jeep, its drying right now before the second coat, I'm very happy I decided to do it! It also makes it ALOT easier that my Jeep is black, I can just fade the stuff out. We did my buddies white Jeep at the same time and it was annoying as hell to cover up all the white paint.

Thanks Dnbearcat for pushing me over the edge to finally do it!
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-07-2009, 08:34 AM   #18
Jeeper
 
mrcarcrazy's Avatar
 
Join Date: Jul 2009
Location: Midland/Odessa, TX
Posts: 3,410
Quote:
Originally Posted by ExDementia View Post
Just Hurculined my Jeep, its drying right now before the second coat, I'm very happy I decided to do it! It also makes it ALOT easier that my Jeep is black, I can just fade the stuff out. We did my buddies white Jeep at the same time and it was annoying as hell to cover up all the white paint.

Thanks Dnbearcat for pushing me over the edge to finally do it!
You know we expect pics.
mrcarcrazy is online now   Quote Quick Reply
Old 10-07-2009, 10:45 AM   #19
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Quote:
Originally Posted by mrcarcrazy View Post
You know we expect pics.
Haha, now I gotta find my camera...
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-07-2009, 01:21 PM   #20
Member
 
Join Date: Mar 2009
Location: Upstate/Eastern NY
Posts: 1,960
Send a message via AIM to thaduke2003
Hmm- I'm looking into doing Briana's and my JK's some weekend here before winter. Just gotta get $ and off my arse Mark W.
thaduke2003 is offline   Quote Quick Reply
Old 10-07-2009, 01:25 PM   #21
Jeeper
 
NeitherFanboy's Avatar
 
Join Date: Sep 2009
Location: Humble, Texas
Posts: 258
Thanks for posting these, I soooo want to do mine (but it's white so it won't be as easy as black -- LOL)
NeitherFanboy is offline   Quote Quick Reply
Old 10-07-2009, 03:43 PM   #22
Jeeper
 
cheap_jeep's Avatar
 
Join Date: Aug 2009
Location: Southeast PA
Posts: 63
neitherFanboy, U-pol makes a product that you can tint to match the vehicle color. So whites not out of the question. Just did my wifes(cheap_jeep) 2 weeks ago. did entire tub though in red. I guess I have to post pics when I get back home.
cheap_jeep is offline   Quote Quick Reply
Old 10-07-2009, 04:39 PM   #23
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Edit.
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-07-2009, 04:40 PM   #24
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Quote:
Originally Posted by NeitherFanboy View Post
Thanks for posting these, I soooo want to do mine (but it's white so it won't be as easy as black -- LOL)
Like I said, my buddies is white, and we just had to do more of a detailed job, but if you think about it, we had to do a better job as a result of that. It made it very easy to see spots we missed, and thus eliminating weak points.

Heres my suggestion, do the fender wells first, then the rear floor, (bed i guess) then the driver and passenger areas. This will make it much easier to do the detail work up around the fender rails around the roll bars because you can climb in there.
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-09-2009, 01:19 PM   #25
Jeeper
 
dirtNsky's Avatar
 
Join Date: Oct 2009
Location: Fredericksburg, VA
Posts: 53
Pedal swap

So now that you have the Herculiner in place and before you re-assemble the interior, have you thought about swapping out the pedals? After I coat my 95 YJ, I want to throw out the factory peddles in favor of steel. Has anyone done it? What pedals do you recommend?
__________________
dirtNsky
dirtNsky is offline   Quote Quick Reply
Old 10-09-2009, 01:36 PM   #26
Jeeper
 
dnbearcat's Avatar
 
Join Date: Aug 2009
Location: Columbus, Ohio
Posts: 54
I dont know about that, mine are still in pretty good shape and i like the rubber gripping. Not sure how steel ones would feel, especially when feet are wet. Might be something to consider, especially if your on a trail and a foot slips off. Just my thoughts.
__________________
1999 Sahara
2" Old Man Emu Lift + 2" Spacers
33" BF Goodrich All-Terrain T/A KO
D44 Front & Rear w/Detroit Trutracs
Currie TJ/XJ Heavy Duty Tie Rod System w/OME Stabilizer
dnbearcat is offline   Quote Quick Reply
Old 10-09-2009, 02:45 PM   #27
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
Quote:
Originally Posted by dnbearcat View Post
I dont know about that, mine are still in pretty good shape and i like the rubber gripping. Not sure how steel ones would feel, especially when feet are wet. Might be something to consider, especially if your on a trail and a foot slips off. Just my thoughts.
My pedals were slippery when my feet were wet or when ever I wear cleats, (which is alot) so I cleaned up my pedals and hurculined them too We'll see how well they hold up, but if it comes off then who cares
__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Old 10-11-2009, 06:07 PM   #28
Jeeper
 
dnbearcat's Avatar
 
Join Date: Aug 2009
Location: Columbus, Ohio
Posts: 54
After a week of dry time i finally put it all back together along with the new Big Boy Seat Brackets. The liner turned out better than i thought and when i got all the seats and what not it looked even better.

The rear seat broken bolt fix ended up being a pain in the butt. We drilled tehm all the way out 5/16'' and tapped them for some new bolts. Seems to have worked out well, they are down nice and tight.

The seat brackets went in pretty easy and i think if you have long legs and limbs it is definitely worth it. You do get about 4 inches, more of room. You can see in the pictures the difference in seats. Needless to say if its back all the way someone behind you better be a child. But i guess you can always scoot back to normal position. I have a 36'' inseam and can extend my left leg all the way out now.


I do have the passenger side brackets and don't think im going to install them so if anyone wants to pick them up for their jeep i can make a deal on them. Just send me a message here or dnbearcat@yahoo.com if you are interested.
Attached Thumbnails
Click image for larger version

Name:	IMG_2439.jpg
Views:	2
Size:	57.2 KB
ID:	11881   Click image for larger version

Name:	IMG_2440.jpg
Views:	2
Size:	62.8 KB
ID:	11882  

Click image for larger version

Name:	IMG_2442.jpg
Views:	2
Size:	41.8 KB
ID:	11883   Click image for larger version

Name:	IMG_2447.jpg
Views:	2
Size:	50.9 KB
ID:	11884  

__________________
1999 Sahara
2" Old Man Emu Lift + 2" Spacers
33" BF Goodrich All-Terrain T/A KO
D44 Front & Rear w/Detroit Trutracs
Currie TJ/XJ Heavy Duty Tie Rod System w/OME Stabilizer
dnbearcat is offline   Quote Quick Reply
Old 10-11-2009, 06:29 PM   #29
Jeeper
 
05GT-O.C.D.'s Avatar
 
Join Date: Sep 2008
Posts: 1,415
Nice job bearcat - looks fantastic!
__________________
When my time comes, mix my ashes with gunpowder encased in brass, point me towards murderer's and pedophile's and let me fly.

(: ˇ ɹǝʌo ǝɯ 11oɹ ...sıɥʇ pɐǝɹ uɐɔ noʎ ɟı
05GT-O.C.D. is offline   Quote Quick Reply
Old 10-11-2009, 09:35 PM   #30
Jeeper
 
ExDementia's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 1,221
I always liked that seat color combination...

What, who me? jealous? Nah!!

I just need to cover my ugly seats

__________________
1991 XJ Cherokee, 4.0, AW4, NP-242, SYE
HP D30, Rusty's axle truss, Currie HD steering, diff. slider
C8.25, Powertrax locker
4.5" RE up front and Rough Country out back
33" BFG A/T's 15" soft 8's
Suspension seats, rock sliders, plated rear corner panels,
trimmed fenders, CB, exhaust, lights, remote locks and start, etc.
Past jeeps:97 TJ, 99 TJ

Quote:
Originally Posted by Geoff@Bestop View Post
In video games, the bad guy's bullets travel much slower than the good guy's bullets.
ExDementia is offline   Quote Quick Reply
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Herculiner DIY jgano23 General Jeep Discussion 29 10-18-2009 08:37 PM
My Herculiner Job nmdriver TJ General Discussion Forum 28 09-23-2009 10:10 PM
Started Herculiner project Iquois General Jeep FAQ/Stickies 36 06-13-2009 12:17 AM
Herculiner Grill rich1014 TJ General Discussion Forum 2 02-25-2007 01:13 PM
Question about Herculiner. amerijeep YJ General Discussion Forum 2 04-15-2005 11:31 PM


logo carid shop wrangler parts carid fender flares custom wheels store avs deflectors at carid

» Network Links
»Jeep Parts
» Featured Product

All times are GMT -5. The time now is 03:16 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC