Good Crank w/o start, dead gages - Jeep Wrangler Forum
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum

Join Wrangler Forum Today


Reply
 
Thread Tools

Please support our sponsors and let them know you heard about them on WranglerForum.com
Old 04-01-2009, 08:20 PM   #1
Newb
 
Join Date: Apr 2009
Posts: 6
Good Crank w/o start, dead gages

i've been searching all over for weeks for someone with the same problems i'm having and cant find anyone so it's time to start my own thread

like the title says. I have a new battery and the engine cranks great, but with no spark, and no pulse at injectors while cranking. I have checked all the relays under the hood, they all work, i've replaced the ign. coil, and dropped in a new distributor along with a new crank position sensor. through my self diagnosis i have come to the conclusion that my ecu is going bad or i have a short somewhere in the wiring harness i cannot find.

a little more on the problem.
My jeep runs, and when it runs it runs like a top. but randomly it seems, while driving, stopped, or parked with ign off. this problem will start up. if i'm driving at the time, my engine will turn off, my voltmeter, fuel gauge, tach, spedo, oil press, and water temp gauges will all drop to zero or dead positions, obviously if the engine just shut off the tach and oil press will read zero but i'm sure the gauge isn't actually reading correctly. lol. this of course is the most frustrating of the situations of this problem acting up, and i'm getting sick and tired of it happening, thus this post

how i "fix" it.
every time i go to start my jeep the first thing i do is turn the ignition on and stare at the volt meter. if it jumps up to 12v i know it'll start otherwise it jumps up maybe an 1/8 of an inch, 1 to 2 widths of the needle. then drop back down to zero. if it reads zero it will crank but not start. one of two things i do usually solve the problem and get it drivable again. 1 I turn the key on, off, on, off till i see volt meter come on. or i go under the hood to the ecu with the key on and unplug the black (i think), on the right side of the ecu towards the engine. anyways i unplug that and plug it in untill i hear what i think is the injectors click in. then when i go back inside my volt meter is up and the car will start.

when the problem happens.
it seems almost as it is completely random, but it does seem to increase when it is humid outside. the last really bad rain we had i couldn't start my jeep for 2 days. causing me to miss a day of work... ouch

oh one more thing. when my jeep wont start and i have the ignition on. if i turn the hazards on, NOT turn signals, with every flash of the hazards my vold meter gauge will jump slightly up

joepowles is offline   Quote Quick Reply
Old 04-01-2009, 08:44 PM   #2
Jeeper
 
Sb5551's Avatar
 
Join Date: Feb 2008
Location: South Philadelphia
Posts: 2,077
When your gauges go dead, does the odometer read no-bus?

I had a cherokee in the shop that read no bus, the crankshaft position sensor went.

On my jeep when I had the same problems as you, my computer had taken a crap I cant remember if it read no bus or not though.

__________________
No more jeep for now
But I have free kandy and kittens in the back of my van


Sb5551 is offline   Quote Quick Reply
Old 04-01-2009, 09:01 PM   #3
Newb
 
Join Date: Apr 2009
Posts: 6
Oh one more thing. 97 sport 4.0L AT

@Sb5551
not sure what it means to read no-bus. i'll look it up
joepowles is offline   Quote Quick Reply
Old 04-08-2009, 04:05 PM   #4
Newb
 
Join Date: Apr 2009
Posts: 6
ok found out some more but still no solution yet.
1 - odometer does not read no-bus, so no problem there
2 - I found a friend with a known good ecm swapped em out and still had the same problems. so that leads me to believe my ecm is still good.

so now i'm looking for a short in the wiring harness i'm guessing. I dont know exactly where to start without just ripping the whole harness out. any suggestions?
joepowles is offline   Quote Quick Reply
Old 04-08-2009, 04:24 PM   #5
tdm
Jeeper
 
tdm's Avatar
 
Join Date: Oct 2008
Location: Everett, WA
Posts: 58
Sounds like you have possibly found your issue...The black plug to the ECM. If playing with it make a change and lets you start the engine, I would begin there. Completely clean the plug and ensure that you have good contact when plugged in. Maybe even use some dialectric grease to help.
__________________
2005 X 4.0 with a 6 speed. 2" BB Toyo 33".

Of course it's the same old story. Truth usually is the same old story.
tdm is offline   Quote Quick Reply
Old 04-08-2009, 05:27 PM   #6
Newb
 
Join Date: Apr 2009
Posts: 6
every plug on the ECM is very clean, and i've put dielectric grease on each plug. i tried that first. *shrug*

that goes for all the relays under the hood too i've gone threw and cleaned all i could think to with no results
joepowles is offline   Quote Quick Reply
Old 04-08-2009, 05:36 PM   #7
tdm
Jeeper
 
tdm's Avatar
 
Join Date: Oct 2008
Location: Everett, WA
Posts: 58
Is it possible that one or more of the wires have "backed out" of the plug? I'm not sure without looking (some plugs are molded), but on most of these type of plugs the wire end is crimped on and then inserted through the back of the plug...they snap into the unit and are only held in place by the little tabs. Sometimes they will back out just enough to create an issue.
__________________
2005 X 4.0 with a 6 speed. 2" BB Toyo 33".

Of course it's the same old story. Truth usually is the same old story.
tdm is offline   Quote Quick Reply
Old 04-08-2009, 06:00 PM   #8
Newb
 
Join Date: Apr 2009
Posts: 6
thought of that as well and i took apart that plug completely. there was nothing wrong with it from what i could tell
joepowles is offline   Quote Quick Reply
Old 04-08-2009, 06:00 PM   #9
Newb
 
Join Date: Apr 2009
Posts: 6
thanks for your help and ideas though
joepowles is offline   Quote Quick Reply
Old 04-09-2009, 05:08 AM   #10
Jeeper
 
Join Date: Jan 2009
Location: no mans land, benton ks
Posts: 611
i know that it may sound kinda dumb, but have you checked ALL of your grounds? from the motor, to battery, then the frame to motor, and the body to frame?
__________________
1977 Cherokee ChiefEdelbrock 1406, 33X12.50, front 1.5 inch shackle lift. AMC 360, th400 Quadra-Trac
2002 wrangler, stock 4.0, auto, 33X12.50 maxis buckshot, AEV Highline Body kit, Ford 9 inch rear end.
Soon to come mods: 4" full traction lift, 4.56 gears, 35X10.50R15 boggers, 35X12.50 cooper st tires, spooled rear end, and much more.
crazyredneck is offline   Quote Quick Reply
Old 04-09-2009, 10:06 AM   #11
Jeeper
 
slf41002's Avatar
 
Join Date: Feb 2008
Location: Augusta,KY
Posts: 1,163
Well it could also be the ignition switch itself or the wiring going down the column from the switch but I would say you are headed in the right direction at this point.I would have to go back and look to see but I had the same issue with my Dodge Dakota and ended up being the main feed wire to the computer.I had to search the Internet for the harness color codes and find the main wire that feed the computer.It did the same exact thing as your for a while but one day it would not start at all and after 3 days being dead I hooked a hot wire to the battery and defibulated its heart As soon as I hooked the hot wire to the wire to the one that I found to be the feed wire it fired right up(now this was after sitting dead for 3 days)I traced the original wire down to find nothing wrong with it so I ran a new wire and it is still running fine that way(that was over a year ago)!!!!!!
__________________
I like for it to shine even thought it is muddy most of the time!
http://www.myspace.com/shermanf
slf41002 is offline   Quote Quick Reply
Old 05-10-2009, 09:18 AM   #12
Newb
 
Join Date: May 2009
Posts: 4
Just read your message after I started a thread just like it. My symptoms are exactly the same even on rainy days. I also noticed that my fuel gauge shows empty along with the amp gauge reading 0. Any luck yet?
coppage is offline   Quote Quick Reply
Old 05-10-2009, 09:40 AM   #13
Jeeper
 
Join Date: Aug 2008
Posts: 2,473
Sounds like either a supply problem or a ground problem.

I think you can use some "T" pins from your wife's sewing basket.
Use a wiring diagram to find which terminals on the ECM are hot and grounds - there are more than one.
Back probe the "T" pins into those wire connections.

Then use a digital voltmeter - record the voltmeter readings KEY ON when it's in the condition it will start. Leave the pins in -- Then next time it won't start, take another set of readings.

The one that's "different" would be the culprit. Then use the wiring diagram to see where it goes and measure at the other end.

It sounds like a connection, like maybe a splice is not right.
Tough to find, but a good wiring diagram, a voltmeter (use a digital meter, they are high impedance,) and patience will resolve it.
__________________
It's no wonder the country is falling apart - stupidity abounds!
rrich is offline   Quote Quick Reply
Old 02-18-2013, 09:25 PM   #14
Newb
 
Join Date: Mar 2010
Posts: 5
Wondering how this was solved

Hi guys,

My 97 Sahara is having this same exact problem. Did anyone figure out the problem? Can you please share the solution with me?

Regards.
SGT DELTA is offline   Quote Quick Reply
Old 02-19-2013, 01:42 AM   #15
Jeeper
 
Buz 1's Avatar
 
Join Date: Sep 2011
Location: Beaverdam, Ohio
Posts: 214
i've been having the exact same problem. the red wire with white marker in the black plug is the main power wire to the pcm. u'll notice that it's a 14 gauge wire, where the rest are 18g.. it enters a plug located right next to the pcm that continues along the firewall into the cab. if u read the fsm it shows u how to pull the plug apart & pull connector out to service.. i just applied dielectric grease to each connector but haven't had a chance to test. seems to be a common issue.. '97 tj...
__________________
'97 TJ, 2.5L 5sp


Buz 1 is offline   Quote Quick Reply
Old 02-19-2013, 06:19 AM   #16
Newb
 
Join Date: Mar 2010
Posts: 5
Thanks Buz,

I'll try that next. I also need to try my other ignition key because the one I'm using seems to be a little worn out.

I'll post my results when I get them.
SGT DELTA is offline   Quote Quick Reply
Old 02-19-2013, 11:07 AM   #17
Jeeper
 
Buz 1's Avatar
 
Join Date: Sep 2011
Location: Beaverdam, Ohio
Posts: 214
i should have also mentioned that to test ignition switch check fuses 9,10, & 11 (behind glovebox) for power, both with key on,, & while cranking. if all good ignition switch is good(tks to 'rubi)...
__________________
'97 TJ, 2.5L 5sp


Buz 1 is offline   Quote Quick Reply
Old 02-19-2013, 11:21 AM   #18
Jeeper
 
BigCrave's Avatar
 
Join Date: Dec 2012
Location: TN
Posts: 275
If turning the ignition key off and on helps, I would look into the swicth itself. If unplugging and plugging back in connector to the ECU works, look into that.
BigCrave is offline   Quote Quick Reply
Old 03-09-2013, 09:19 PM   #19
Jeeper
 
Falcho's Avatar
 
Join Date: Jun 2012
Location: North Pole, Alaska
Posts: 52
Greetings all,
So my 97 TJ was running just fine. I parked in at the end of December. Went to start it today, battery was completely dead. Once I charged it, I got the no gas/voltmeter working, no start situation. Im at a loss. All I did was park it for 2.5 months. Did any of you come up with something I can try?
Falcho is offline   Quote Quick Reply
Old 03-10-2013, 06:21 AM   #20
Jeeper
 
Buz 1's Avatar
 
Join Date: Sep 2011
Location: Beaverdam, Ohio
Posts: 214
well,,, if u read this far through the thread u should know what plug we're talking about. mess with it with ign. switch on & heater blower off so u can hear real well,, & u'll be able to hear the sensors click & the fuel pump run when they get power. i 1ce again pulled the plug apart & lightly crimped connectors a10, a11, a19, & a20, all 4 of which control the iac( m-lite on since i bought it.) earlier i had crimped a2, a4, a22(fused +), a31, & a32(both grounds). if u look at the face of the plug that goes into the pcm u'll see that each connector is numbered.. also,, before i crimped anything i filled each female connector with dielectric grease. it's working better since...
__________________
'97 TJ, 2.5L 5sp


Buz 1 is offline   Quote Quick Reply
Old 03-10-2013, 02:42 PM   #21
Jeeper
 
Falcho's Avatar
 
Join Date: Jun 2012
Location: North Pole, Alaska
Posts: 52
Well,
I played with the pcm connectors best I could, which was unplug and replug at this point. I have no garage, and I am in Alaska, and its too nippy to play around trying to disassemble the plastic connectors, which always break at these temps. Anywho, plugging and unplugging had no effect whatsoever. So, until I get another 40 degree day I guess the jeep will have to sit.
Hoping to check the ignitions fuses while I wait, I can do that with no damage. At this point, weather restricts me. Good thing the jeep is not my primary vehicle at this point....
Falcho is offline   Quote Quick Reply
Old 03-16-2013, 04:12 PM   #22
Jeeper
 
Falcho's Avatar
 
Join Date: Jun 2012
Location: North Pole, Alaska
Posts: 52
It warmed up enough today to break out the meter. The CPS is not getting 5 volts. So, it appears the problem is in the pcm. I have scoured the internet for any way to test a pcm, and it seems to be apparent that there is no test available, you just need to buy one and hope for the best. Im not at that point yet, since the cold is keeping me from doing anything more then the absolute minimum to check things. (30 below wind chills today with clear sunny sky). One person said it could be the ignition switch not sending a signal to the pcm, due to a failure. Again, too cold to tear the steering column down.
The pisser is that this thing ran fine since the day I bought it, until I let it set for 6 weeks, and the battery went dead. I find it hard to believe that sensors, or wires or what not just magically failed while sitting frozen. And since I find dozens upon dozens of references to this exact problem, with no particular cure, I really dont even know what to try next. I sure dont want to give it to the jeep dealer, thats like setting money on fire.
Any new suggestions kids?

Falcho is offline   Quote Quick Reply
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
good times at IHOP.... khenderson Off-Topic 30 06-23-2011 11:48 PM
Takes forever to start.. Mike2000 General Jeep Discussion 7 04-10-2011 10:42 AM
Jeep no start, crank, sudden... jonota TJ General Discussion Forum 1 12-13-2007 11:13 AM
94 yj will crank but wont start Devil Doc YJ Tech Forum 1 08-09-2007 05:33 PM
Window Crank woes, did any one else have this problem? virtual_verve11 JK Tech Forum 2 04-07-2007 09:57 AM


logo carid shop wrangler parts carid fender flares custom wheels store avs deflectors at carid

» Network Links
»Jeep Parts
» Featured Product

All times are GMT -5. The time now is 02:07 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC