Carb and sputtering questions/issues - Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum

Join Wrangler Forum Today



Reply
 
Thread Tools

Please support our sponsors and let them know you heard about them on WranglerForum.com
Old 07-27-2010, 01:59 PM
Thread Starter
  #1
Jeeper
 
Peloquin's Avatar
 
Join Date: Jul 2010
Location: DFW
Posts: 61
Peloquin is on a distinguished road
Carb and sputtering questions/issues

Hello,

Got a question for you mechanical types (yes yes, i'm working on that inclination in myself).

I have a 1990 6cl 5sp, it has the stock 2bl carb on it. since I purchased the jeep about 4 or 5 years back, i've replaced a number of things on it:
plugs, wires, o2, pgr, alternator, trans, clutch, rear main, battery, cat, muffler, exhaust manifold, fuel filter. i'm down to the last few things under the hood to replace. i've got my eye on replacing the dist, cap/rotor and coil next, as well as possibly the carb.

Here's what it's doing. Just got the trans working again. i've noticed recently, right before my trans issue, that the engine sputters a bit unless i am steadily accelerating in the lower gears. this is instantly noticeable in the first 3 gears if you back off of the gas for a second. even if you are in a gear, at neighborhood speeds. lets say i'm in 3rd running about 35 mph. this would normally be a perfectly fine speed/rpm combo for this gear. lately, when doing this, it sputters, making me speed up. so now it's time to shift into 4th, or coast in neutral if going downhill or upcoming stop. so i get into 4th, and in the lower end and middle of the gear, same thing. it's not until i get into 5th, and keep it over 60 that this stops. now, if i let of the gas at all, even at that speed, it'll sputter a little. like it's having problems breathing or something.

i'm assuming the carb probably needs to be rebuilt, at the very least, or replaced. now, I don't give a crap about swapping out the motor for a V8, or putting in the military grade carb that will let me drive through 18 feet of water with 25% more hp than the stock. i just want the thing to run, i don't need it modified. so my question is, does this sound like a vacuum issue in the carb? will replacing it be better than rebuilding the one i have? i saw some rebuild kits, but they specified that they do not include the stepper motor and vacuum cylinder. i found the stepper motor in an exploded view. not sure where or what the vacuum cylinder is, if i have one, if it is needed, all that.

i need some direction. anyone have any ideas?
__________________
(O||||O) 2014 JK with pirate wheels.

"All right. But you tell that slag, that in the ghetto, washing non-colourfast synthetics at 60 degrees could cost you your life... "
Peloquin is offline   Quote
Old 07-28-2010, 01:16 AM   #2
Jeeper
 
tlrrob1000's Avatar
 
Join Date: Jul 2009
Location: Pain is a gift...Fear is not an option!
Posts: 787
tlrrob1000 is on a distinguished road
Hey Peloquin. Get your rebuild kit and knock that out, only 25.00. Welding tip cleaners are a great thing to have when you do this. Punch every jet, orfice and tube. Biggest problem is that they get dirty. Once you do the rebuild and get it running check your timing. Then you can move on to replacing your vacuum lines later. Start your air/fuel mixture screws at 2 1/2 out also.

__________________
No Bad Days!
tlrrob1000 is offline   Quote
Old 08-10-2010, 09:24 AM
Thread Starter
  #3
Jeeper
 
Peloquin's Avatar
 
Join Date: Jul 2010
Location: DFW
Posts: 61
Peloquin is on a distinguished road
i'll give that a try. still haven't had the time/ money to get on this project. i'm thinking I might try the cap/rotor and coil first, just to ensure i'm not doing something that doesn't need to be done. then if i'm still getting the same symptoms, on to more money.
__________________
(O||||O) 2014 JK with pirate wheels.

"All right. But you tell that slag, that in the ghetto, washing non-colourfast synthetics at 60 degrees could cost you your life... "
Peloquin is offline   Quote
 
Old 08-10-2010, 10:09 AM   #4
Jeeper
 
Just-Jimmy's Avatar
 
Join Date: Jul 2010
Location: Lakeland Florida
Posts: 25
Just-Jimmy is on a distinguished road
Sounds more like a Carb problem than cap and rotor. The original carbs are crap. Get a Weber. I know you do not care about a horsepower increase, but do you care about a fuel economy and reliability increase? If so, do not waste your time rebuilding the stock carb.
Just-Jimmy is offline   Quote
Old 08-10-2010, 10:43 AM   #5
Newb
 
Join Date: Aug 2010
Posts: 2
Brooklin Cheetah is on a distinguished road
You should look into a 'nutter bypass' (google it) and a carb swap with either a weber, or the motorcraft 2100 carb.
Brooklin Cheetah is offline   Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
4.2 carb problems stray YJ Tech Forum 25 10-27-2016 01:16 AM
Very Sad I bought a Lemon... Jahaira_JeepYJ89_fan YJ General Discussion Forum 19 07-13-2007 03:01 PM




All times are GMT -5. The time now is 10:59 AM.


User Alert System provided by Advanced User Tagging v3.1.0 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC
« Back

Enter your email address:

Delivered by FeedBurner