Monstalining the Tub Question? - Page 4 - Jeep Wrangler Forum
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum

Join Wrangler Forum Today


Reply
 
Thread Tools

Please support our sponsors and let them know you heard about them on WranglerForum.com
Old 12-19-2012, 01:30 PM   #91
Jeeper
 
tigerblood's Avatar
 
Join Date: Oct 2012
Location: Waterloo, IA
Posts: 1,437
Quote:
Originally Posted by cowboy17 View Post
looks fantastic.
But why put carpet back in? Me no comprende....
x2

__________________
4.0 power tech>32RH>231j>4:10>33" BFG's
tigerblood is offline   Quote Quick Reply
Old 12-19-2012, 07:46 PM   #92
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by Cowboy17 View Post
looks fantastic.
But why put carpet back in? Me no comprende....
Quote:
Originally Posted by tigerblood View Post
x2

Yeah I know it seems counter productive to put carpet over liner but I have a couple reasons why I did it.

The main reason is to keep the heat down in the cab. It's miserable hot in Arkansas in the summer and I don't have AC. I take the top off in early spring and don't put it back on until December, rain or shine the Jeep is driven only with a bikini top. I don't worry about everything getting wet since the Jeep stays open and dries out well, but without some kind of barrier between the floor and the seats the heat coming up gets really uncomfortable.

I was going to go with a rubber mat but thats where my second reason comes in, my wife didn't like the idea of rubber mats VS carpet. The compromise is there's only carpet in the front portion of the cab, right under our feet, and no where else.

I made sure to pull all the drain plugs in the front and directly behind the front seats so I should get good drainage. I did the same thing with my 87YJ and never had a problem with the carpet getting mildewed or rotting. I figure the liner being water resistant will take care of the risk of rust, which is the main reason I put it down. I want this Jeep to last since I don't plan to sell it like I did my 87, still regret that.

Lincoln33 is offline   Quote Quick Reply
Old 12-20-2012, 12:59 AM   #93
Jeeper
 
Sandstorm95's Avatar
 
Join Date: Mar 2012
Location: Long Island
Posts: 182
I know a few people who did what you did your not that crazy d w . I have those same smitty tube steps and I had to drill holes in the bottom because water was pooling up inside them. Had to sand that all off and throw some durabak on them. Pretty much anything that I need to take a beating i coat. Hardtop step ups gas tank skid plate etc. Love this stuff
Sandstorm95 is offline   Quote Quick Reply
Old 12-20-2012, 03:51 PM   #94
Jeeper
 
89quest's Avatar
 
Join Date: Oct 2012
Location: conway,n.h
Posts: 374
Everything is looking great, I have been following your thread since the beginning and I have the shifter area and drivers seat left before starting the prep on my 89yj.Thanks for the inspiration!!!
__________________
1989YJ 2.5L TBI 5spd. 2" body/4" susp. Lift/33x12.50x15 Pro Comp Mud Terrain
89quest is offline   Quote Quick Reply
Old 12-21-2012, 08:28 AM   #95
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by Sandstorm95 View Post
I know a few people who did what you did your not that crazy d w . I have those same smitty tube steps and I had to drill holes in the bottom because water was pooling up inside them. Had to sand that all off and throw some durabak on them. Pretty much anything that I need to take a beating i coat. Hardtop step ups gas tank skid plate etc. Love this stuff
Quote:
Originally Posted by 89quest View Post
Everything is looking great, I have been following your thread since the beginning and I have the shifter area and drivers seat left before starting the prep on my 89yj.Thanks for the inspiration!!!
Thanks for the good words guys, I'm nearing the end of this and should be back on the road soon. The works been theraputic but I'll be glad when it's done.
Lincoln33 is offline   Quote Quick Reply
Old 12-23-2012, 03:05 PM   #96
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
I got back to work sorting the rollbar pad issue. Here's the spot I was talking about earlier that should have had a bolt hole already in place.







I guess the manufacturer doesn't punch a hole for you due to different fits for different Jeeps, or maybe in case you don't use the rollbars that attach to the windshield. Either way I needed a hole there and didn't want to just punch a hole that would fray or split out so I picked up a grommet kit.

I marked my spots while the pad was on the rollbar.



Used the punch that came with the kit for a clean hole





Hammered in the grommets and reinstalled the pads







Like most of the other areas that had torx bolts I replaced them with stainless hex head bolts.

Lincoln33 is offline   Quote Quick Reply
Old 12-23-2012, 03:32 PM   #97
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
I also got all my seatbelts reinstalled. I did have some trouble there, I couldn't get the belts to unlock from the retracter. I knew I had seen something on WF about it so I had to take a break and do a search to figure out what I was doing wrong. The cause of the problem was me not holding the seatbelts completely level while trying to pull the belt out. As soon as I figured that out no more problems.




The last thing I did was install the Instatrunk. I know some folks don't care for these but I had one on my 87YJ and it came in handy. Since I pulled the carpet from the rear tub area it wasn't a snug fit, I used washers to snug it up and prevent it from bowing out.






I'm gonna try to get the rails for the top bolted on next but it may have to wait until after Christmas.

I hope all of Ya'll have a good Christmas.
Lincoln33 is offline   Quote Quick Reply
Old 01-09-2013, 09:15 PM   #98
Newb
 
Join Date: Sep 2012
Posts: 7
Waooow

I'm really impressed by the quality of both your work and your thread.
Right now, I'm preparing the job on my 99 TJ. Removed the seats (front and back), console, etc... Had a hard time with one-two Torx of the rollcage. I stripped them but read that you had to solder a nut over to take them out. I'll give it a try.
Thanx a lot for your thread, really instructive !
I wish you all the best for 2013 !!!
LoloTheJeeper is offline   Quote Quick Reply
Old 01-10-2013, 10:41 AM   #99
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by LoloTheJeeper View Post
I'm really impressed by the quality of both your work and your thread.
Right now, I'm preparing the job on my 99 TJ. Removed the seats (front and back), console, etc... Had a hard time with one-two Torx of the rollcage. I stripped them but read that you had to solder a nut over to take them out. I'll give it a try.
Thanx a lot for your thread, really instructive !
I wish you all the best for 2013 !!!
Thanks for the good words. I managed to pull the torx bolts using vice grips, they gave me just enough grip to turn the bolts. As you can see from the thread I replaced them with hex heads.

I'm still working this project but I had a few set backs due to the ice storm that hit Arkansas on Christmas day. I had several trees and bushes damaged and have been doing clean up around the house instead of working on the Jeep. As soon as I get back to the Jeep I'll post some more pics, hopefully showing the finished product.
Lincoln33 is offline   Quote Quick Reply
Old 01-10-2013, 06:44 PM   #100
Jeeper
 
89quest's Avatar
 
Join Date: Oct 2012
Location: conway,n.h
Posts: 374
I can't say enough about your attention to detail, great thread and awsum work. Thank You
__________________
1989YJ 2.5L TBI 5spd. 2" body/4" susp. Lift/33x12.50x15 Pro Comp Mud Terrain
89quest is offline   Quote Quick Reply
Old 01-10-2013, 08:06 PM   #101
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by 89quest View Post
I can't say enough about your attention to detail, great thread and awsum work. Thank You
Thanks man, I appreciate the compliments.
Lincoln33 is offline   Quote Quick Reply
Old 01-11-2013, 02:46 AM   #102
Jeeper
 
Join Date: Aug 2009
Location: Hinesville, Ga
Posts: 222
Great job Lincoln!!!!! I see the ear plugs worked well for you too. I had no issues using them in mine and had to pass on what I used to you. Looks GREATTTTTTTTT
tim2 is offline   Quote Quick Reply
Old 01-11-2013, 10:48 AM   #103
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by tim2 View Post
Great job Lincoln!!!!! I see the ear plugs worked well for you too. I had no issues using them in mine and had to pass on what I used to you. Looks GREATTTTTTTTT
Thanks man, the ear plugs worked like a charm. I only had to chase a couple threads but that was due to old age and not from the liner getting past the plugs.
Lincoln33 is offline   Quote Quick Reply
Old 01-30-2013, 07:12 AM   #104
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Well it took longer than it should have but I finally finished this project and now the Jeeps back on the road. Here's a few more pics showing what I did as I wrapped it up.

I bolted the top hardware back on using stainless hex head bolts. The bolts stand out more than I thought they would but I'll get over it. I thought they were going to get in the way when putting the top up but once the bolts were tightened down everything worked fine. Although the Monstaliner has a thick coat to it there weren't any fitment issues when I reinstalled the hardware.







The old seat belts were in bad shape so I bought some new ones for the front seats, I cleaned up the old belts for the back seat.

Lincoln33 is offline   Quote Quick Reply
Old 01-30-2013, 07:51 AM   #105
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
I bought a new console and had to do a little extra work to get the fit I wanted. The stock console sat too low and with the new Corbeau seats I knew I'd be sitting higher than stock and I didn't want to have to lean sideways to use the armrest. As you can see from the picture I installed the bracket on the front thats actually supposed to be on the rear of the console.



To make the console sit higher and level I had to make a taller bracket for the rear.





The metal wasn't really that thick but I used heat on it anyway to get a cleaner bend since I don't have a metal brake.



The bends were rounded and a little wider than the stock bracket but they worked.








Without the seats in place the console looked to be too high.





I wasn't sure how it would look so I just took a chance and made my cuts and bends and hoped for the best.





Due to the seatbelts creating a tight fit I had to bend the bracket to the inside instead of the outside. I had to work on this for a while to get the bends even so the bracket would sit level.



Drilled, painted and mounted in place. I ended up moving the console forward after I decided it was taking up too much leg room from the back seat area. Then I noticed it was a little close to the transfer case shifter but I had already bolted the brackets in place. I still haven't checked to see if it's going to be a problem but if it is I'll leave the brackets in place and unbolt the console and slide it back a little.





Lincoln33 is offline   Quote Quick Reply
Old 01-30-2013, 08:28 AM   #106
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Finally getting the seats bolted in, this was easier said than done. I won't go on a long rant but will say I ran into several problems with my "Universal Fit" seats. They didn't work with my stock brackets, as I was told they would. Then I was sent the wrong adapters and had to work an exchange and wait an additional week to install the seats. The new adapters came with mismatched bolts and nuts that didn't work so I had to buy nuts and bolts that would. I'm not going to bash any particular company but man was this frustrating to deal with. In the end I got the seats installed and thats what mattered.

Like everything else I replaced the stock bolts with stainless hex heads.





Here's the seats installed next to the console. Although the console looked too high when I installed it you can see it's the right heighth for the seats that sit higher than stock.







The seats definitely sit higher than I expected and have a reclining lean to the rear that can't be adjusted. Overall they're comfortable to sit in but if you were someone that's a little wide in the hips they might not be comfortable over the long haul. The back seat was a breeze to install but it is a little smaller than the OEM seat.





The last thing to do was reinstall the doors. No fitment problems from the Monstaliner and everything works good.






Many Thanks to everyone that gave me tips and helped me along the way
Lincoln33 is offline   Quote Quick Reply
Old 01-30-2013, 02:43 PM   #107
Jeeper
 
Sandstorm95's Avatar
 
Join Date: Mar 2012
Location: Long Island
Posts: 182
Those corbeaus look like your gunna be driving around gangsta style leaning back
Sandstorm95 is offline   Quote Quick Reply
Old 01-31-2013, 10:03 AM   #108
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by Sandstorm95 View Post
Those corbeaus look like your gunna be driving around gangsta style leaning back
Yep, and I don't think I can pull off the gangsta thing at my age.
Lincoln33 is offline   Quote Quick Reply
Old 01-31-2013, 10:34 AM   #109
Jeeper
 
Join Date: Nov 2012
Location: PHX
Posts: 20
Are those the baja jp seats that are suppose to be a direct fit for yjs?
RR14 is offline   Quote Quick Reply
Old 01-31-2013, 03:22 PM   #110
Jeeper
 
StanF's Avatar
 
Join Date: Jan 2013
Location: Austin, TX
Posts: 867
Quote:
Originally Posted by Lincoln33 View Post

The last thing I did was install the Instatrunk. I know some folks don't care for these but I had one on my 87YJ and it came in handy. Since I pulled the carpet from the rear tub area it wasn't a snug fit, I used washers to snug it up and prevent it from bowing out.




Could you give a quick review of the Instatrunk fit, security, water-tightness, value, etc?

I'm either going to weld one up or buy one. Would love to hear your thoughts. I've also removed my carpet, and would have the same gap.

Thanks!
StanF is offline   Quote Quick Reply
Old 02-01-2013, 09:44 AM   #111
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by RR14 View Post
Are those the baja jp seats that are suppose to be a direct fit for yjs?
They're the CORBEAU Baja SS Suspension Seats. The web site description said they fit:

87-95 Jeep Wrangler (YJ)
Universal Fit - This part will fit most vehicles. Some universal fit products require that you select a specific size or style, based on the actual features on your vehicle.

Since the description said "universal fit" and there was mention of an adapter bracket I called the distributor and asked a "tech" if I needed the adapter bracket, he said "No". I ordered the seats a month before I started this project and had them sitting around for a while before it was time to install them. When I finally got to the point of installation that's when I found out the seats wouldn't work with my stock brackets. I called the distributor back and ended up ordering the adapters.

Here's a couple pics to show why the seats wouldn't work without adapters. The Baja seats have tabs welded to the seat frame. Directly behind the tabs you can see the screws that come up from the stock seat bracket and bolt to the adapter.





Here's what the stock seat bottoms look like. They don't have tabs and sit flat on the stock seat brackets.



If you're going to order the Corbeau seats and you want to use your stock brackets make sure you get the seats that sit flat on the seat brackets, don't get the universal fit with the tabs. I wish I knew this ahead of time to save myself some grief and a couple dollars. Live and Learn
Lincoln33 is offline   Quote Quick Reply
Old 02-01-2013, 10:10 AM   #112
Jeeper
 
UNCLE BS's Avatar
 
Join Date: Oct 2012
Location: North West North Dakota
Posts: 37
So now do your seats sit higher using the brackets?
__________________
87 YJ, 350TBI, AtlasII,700R4,Dana60 HP Front, 14bolt rear,ARB'S, Tom Woods custom shafts, lots more
UNCLE BS is offline   Quote Quick Reply
Old 02-01-2013, 10:25 AM   #113
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by StanF View Post
Could you give a quick review of the Instatrunk fit, security, water-tightness, value, etc?

I'm either going to weld one up or buy one. Would love to hear your thoughts. I've also removed my carpet, and would have the same gap.

Thanks!
This is the second Instatrunk I've installed, the first one was in my 87YJ. I left the carpet in on that one and the fit was definitely better. I still got water in the storage area whenever it rained and I had the top off, it soaked in through the carpet. I used a waterproof bag to keep tools and other items dry.

With my 93 I'm planning to put a tray in the cargo area that will elevate whatever is in the trunk about an inch to keep it from setting in water. As you can see from the pics there's a pretty good gap that will let water in the cargo area. As long as my gear isn't sitting in water it should be okay.





As for security I think the Instatrunk is better than a locking console and definitely better than nothing. I don't leave anything of real value in my Jeep but it's nice to have a locking trunk for tools or other small items.

If I had a metal brake and some talent I would have tried to fab my own. If I remember right the trunk cost about $150 or near that. The price for the metal alone would be considerably cheaper and if you already have the tools then fabbing your own would be the way to go. I saw a thread, I think it was in the builders section, where a forum member fabbed his own, it came out nice and I'm sure he saved some bucks.
Lincoln33 is offline   Quote Quick Reply
Old 02-01-2013, 10:30 AM   #114
Jeeper
 
Lincoln33's Avatar
 
Join Date: Aug 2012
Location: Central Arkansas
Posts: 184
Images: 196
Quote:
Originally Posted by UNCLE BS View Post
So now do your seats sit higher using the brackets?
Yep, probably two to three inches higher than stock. I have to have the tilt steering all the way up and the seat all the way back to get in and out of the driver seat. It's a little iritating but the seats are comfortable to sit in, for short trips anyway. I haven't been on a long haul yet so I'm not sure how they'll be for extended seat time.

Lincoln33 is offline   Quote Quick Reply
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off




» Featured Product

All times are GMT -5. The time now is 07:41 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC