SRC front stinger JK - Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum

Join Wrangler Forum Today

Thread Tools

Please support our sponsors and let them know you heard about them on
Old 06-11-2013, 12:46 PM   #1
Join Date: Jun 2011
Location: Lower Westchester
Posts: 31
mrMangoTango is on a distinguished road
SRC front stinger JK

I just got my SRC front stinger and had a couple of questions about what to do with the existing fog lights... I intend on getting the rigid LEDs to mount on the bumper, but until then where should I put the existing wiring to prevent any problems.

and is wiring to the fog lights simple, i installed kc daylighters on the windshield by myself, should i have a problem doing these?

thanks in advance
mrMangoTango is offline   Quote
Old 06-11-2013, 01:16 PM   #2
Get your Jeep dirty!!!

WF Supporting Member
Rogerg's Avatar
Join Date: Aug 2009
Location: Las Vegas
Posts: 762
Rogerg is on a distinguished road
Should be wired almost the same as the KCs.
I just tucked the wires in a corner with zipties till i was ready to install the lights.

2008 Jeep X unlimited 4" Rancho Sport lift/17x9 Black Level 8 Alloys/37-12.5-17 Nitto Trail Grapplers
2006 Jeep Rubicon 5.5" Teraflex long arm+1" body lift/17x9 Procomp 7031 Alloys/37-12.5-17 Falken Wild Peak
Rogerg is offline   Quote
Old 06-11-2013, 01:16 PM   #3
Wranglin4Life's Avatar
Join Date: Apr 2013
Location: Maryland
Posts: 2,553
Wranglin4Life is on a distinguished road
If you want a clean install I think the only way you are going to be able to do it is drill a hole in the bumper, put a small rubber grommet in and run the wires through the bumper down to the bottom and then under and up into the hood compartment.
Wranglin4Life is offline   Quote
Old 06-11-2013, 04:53 PM   #4
gr8fulKID's Avatar
Join Date: Jan 2012
Posts: 849
gr8fulKID is on a distinguished road
if you never intend on using the stock fog lights again, I would cut the wire on both lights right behind the bulb. Wrap the ends in electrical tape and zip tie them outa sight, theres a few good spots on the frame to do that.

As long as your new lights are 55wats, you can use the existing fog light harness. All you would have to do is splice the ground and power wires from your stock harness into the new lights using wire nuts or butt splices. 4 connections and that's its. Then wrap some wire loom around it and your good.
gr8fulKID is offline   Quote

fog lights , stinger

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Download our Mobile App

» Featured Product

All times are GMT -5. The time now is 10:35 PM.

User Alert System provided by Advanced User Tagging v3.1.0 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC
« Back

Enter your email address:

Delivered by FeedBurner