Help me Please - Jeep Wrangler Forum
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum

Join Wrangler Forum Today


Reply
 
Thread Tools

Please support our sponsors and let them know you heard about them on WranglerForum.com
Old 06-27-2010, 12:28 PM   #1
Newb
 
Join Date: Jun 2010
Location: columbia Il
Posts: 4
Help me Please

Just put a 4 in suspension lift from skyjacker on my Jeep wrangler tj 2000 wont go into 2 4 or Reverse any suggestions....

aaronf00tj is offline   Quote Quick Reply
Old 06-27-2010, 12:31 PM   #2
Newb
 
Join Date: Jun 2010
Location: columbia Il
Posts: 4
grinded down the floor board about 3/8 of an inch back. shifted fine when I didn't put the center console in. but after I put center console it wouldn't shift

aaronf00tj is offline   Quote Quick Reply
Old 06-27-2010, 12:34 PM   #3
Jeeper
 
spyjeep0520's Avatar
 
Join Date: May 2010
Location: south east texas
Posts: 155
did you check to make sure your shifter was put back in the gear slot you pulled it out of
spyjeep0520 is offline   Quote Quick Reply
Old 06-27-2010, 12:36 PM   #4
In a trailer in the woods

WF Supporting Member
 
Barrie's Avatar
 
Join Date: Feb 2008
Location: Greater downtown Brownsville,Kentucky
Posts: 39,336
Send a message via AIM to Barrie Send a message via Yahoo to Barrie
Check to see if the shifter is hitting the console anywhere.
__________________
2006 Unlimited Soft Top


Skillfully disguised as a responsible adult


Barrie is offline   Quote Quick Reply
Old 06-27-2010, 12:39 PM   #5
Jeeper
 
Luckrider's Avatar
 
Join Date: May 2009
Location: Hudson Valley New York
Posts: 33
Did you use the transfer case drop? You will need to adjust the transfer case linkage. The best solution is to get rid of the transfer case drop with a slip yoke eliminator kit and a new CV drive shaft. Getting rid of the transfer case drop will return the transfer case back into its original position in relation to the body and should make shifting better.
Luckrider is offline   Quote Quick Reply
Old 06-27-2010, 01:08 PM   #6
Newb
 
Join Date: Jun 2010
Location: columbia Il
Posts: 4
I cant tell if it is hitting the console. But it is not hitting any metal. I can see that from under the jeep but with me lowering the transfer case you think it could have shifted the transmission to sit unlevel and that is why it would go in gear.. because the shift patterens have changed alot. there more set back to the rear of the jeep if you know what I mean.
aaronf00tj is offline   Quote Quick Reply
Old 06-27-2010, 04:39 PM   #7
Newb
 
Join Date: Jun 2010
Location: columbia Il
Posts: 4
thanks for everyone Help found out what the problem was.. Since it would not go into 2nd 4th or reverse I looked to see what was going on, and why it wouldn't go back. Found after the 4 in lift and transfer case lowering kit it drop the tranny slanting downwards to the rear end.( which I should have known) But I found that after taking the boot off the gear shifter it was clearing the center console barrley but it was. Found out that the damn boot would not let it go back as far as it needed to set in the gear. Took the boot of and is going to have to make a different boot which will give me more room. That might sound a litte hoosier but I do live in SO ILL so I dont fell so bad. Hope it may help someone and If you think I should do something else to it let me know because I don't want to screw the Jeep up. Thanks

aaronf00tj is offline   Quote Quick Reply
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off




» Network Links
»Jeep Parts
» Featured Product

All times are GMT -5. The time now is 01:23 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC