Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Spiderwebshade grommet holes don't line up with soundbar screws

Join Wrangler Forum Today


Thread: Spiderwebshade grommet holes don't line up with soundbar screws Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-12-2011 02:48 PM
DThor35 X 3 here too....
05-11-2011 10:33 AM
jimmyzwheelz Nice response from the vendor...that's great customer service!

I love my top, but never understood how you could leave it in place with the hard top for the very reasons you mention above!

"With all the hardtop's latches needing secured above the front seat and being obstructed by the shade top, it's seems easier to just remove the shade top entirely when the hardtop goes on."

I too would love to see a video on how this is accomplished!
05-10-2011 09:19 PM
Texasflusher Thanks SpiderWebShade for yesterday's response. My wife and I worked more with the top today to see if we can keep the shade top on the same time as the hardtop. With all the hardtop's latches needing secured above the front seat and being obstructed by the shade top, it's seems easier to just remove the shade top entirely when the hardtop goes on. With that said, there is no longer a need to have the grommet holes match where the soundbar screws go.

Has SpiderWebShade or anyone else made a video on installing the 3-piece unlimited hardtop over the shade top? I would love to see one.

Thanks again SpiderWebShade for your offer to replace our top for another.
05-09-2011 08:38 PM
SpiderWebâ„¢
SPIDERWEBSHADE /// with Freedom top

Hey Texasflusher,

Have you tried to release a few of the SpiderBalls in the front and rear? If you release some of the tension you can wiggle to top into position for you bolts. Then you can replace the SpiderBalls as they will stretch quite a bit.

If for some reason this does not work we will be happy to replace your top.

Hope this helps! We loved your video!!!
05-07-2011 09:28 PM
Texasflusher I did not mention earlier that this is for an unlimited.
05-07-2011 09:46 AM
Texasflusher Here are the two holes
05-07-2011 09:11 AM
Texasflusher The two grommet holes should have been placed about an inch further back so unfortunatley flipping over the top wont help but thanks for idea.
05-07-2011 06:59 AM
jeffk42
Quote:
Originally Posted by tommyb View Post
I bought the SpiderWeb SW1 JK-2D TrailMesh top for my JK. Are you sure you purchased a spiderwebshade for a JK and not another model Jeep? I'm pretty sure that all of the tops for JK's do not have "holes" in the middle of the top. There are plenty of grommet holes on the side of the spiderwebshade to position it anywhere you want on your rollcage. Mine pretty much looks like the picture on the website, and I absolutely love it!
They have a free option to add grommets in the center for use with the Freedom Top screws if you have a hardtop. It's not shown on the website, but it's an option you can request.


OP -- I'm sure this is a stupid question, but are the grommets both equidistant from the center? If not, did you try flipping it over?
05-06-2011 10:50 PM
nvkid Same here.
05-06-2011 10:46 PM
tommyb [QUOTE=Texasflusher;1224363]Does anyone else have mis-aligned center grommet holes that will not allow the two large screws that hold the front freedom tops to be inserted through the soundbar? We would like as advertised to keep the webshade on the same time the hardtop is on. There is no way ours can be the only defective top. They are about an inch off. We have an email into the spiderwebshade company about this.
Anyone else have this probl

I bought the SpiderWeb SW1 JK-2D TrailMesh top for my JK. Are you sure you purchased a spiderwebshade for a JK and not another model Jeep? I'm pretty sure that all of the tops for JK's do not have "holes" in the middle of the top. There are plenty of grommet holes on the side of the spiderwebshade to position it anywhere you want on your rollcage. Mine pretty much looks like the picture on the website, and I absolutely love it!
05-06-2011 09:52 PM
Texasflusher
Spiderwebshade grommet holes don't line up with soundbar screws

Does anyone else have mis-aligned center grommet holes that will not allow the two large screws that hold the front freedom tops to be inserted through the soundbar? We would like as advertised to keep the webshade on the same time the hardtop is on. There is no way ours can be the only defective top. They are about an inch off. We have an email into the spiderwebshade company about this.
Anyone else have this problem?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:04 PM.



Jeep, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC