|06-22-2011 04:17 AM|
I have a light addiction that I'm battling.
Don't be a pic-tease; it turns your Jeep blue...
|06-21-2011 09:41 PM|
|Big Kid||Hilldweller, your headlights look awesome!! Where'd you get them?? Sorry to hijack the thread, caught my eye. Thanks.|
|06-21-2011 06:59 PM|
i figured it out, got them to work with ease
.. thank you for all of the help
|06-21-2011 12:57 PM|
That will work for you. You will use the battery ---- but through the relay.
If you don't understand the diagram, find a local mentor to help out. Most gear-heads and wheelers are more than happy to share some wisdom like this.
|06-21-2011 12:37 PM|
|mrMangoTango||I just got the KC Daylighters and everything is all wired up fine except for the switch. if i dont wire it to the battery where do i wire it? pictures would be very helpful. SHould i do it to the cig lighter? if so how do i do that?|
|06-21-2011 11:46 AM|
|06-21-2011 11:41 AM|
|Vinny13||I can post a bunch of pictures as well when I get off work.|
|06-21-2011 11:36 AM|
Take off the side panel of you dash (either side) You will see a nickel sized foam filled hole. You can run the wire through there with a coat hanger. then you can easily drill through the dash to mount the switch.
|06-21-2011 10:49 AM|
Wow, good little thread here. Lots of knowledge crammed in efficiently--thanks Bill.
I'm eventually going to mount A-pillar lights and actually believe I know less about wiring and electricity than my 3-year-old daughter. Got to remember this one . . . .
|06-21-2011 10:35 AM|
Here's a simple diagram:
And here's what I did; ymmv:
I used a full harness from Rallylights.com connected to the passenger side OE headlight circuit and upgraded my headlights. First to Hella H4, then Cibie H4, then to JW Speaker #8700 LEDs. Simple, complete, legal.
My OE fogs were just a bulb swap and retained OE function.
Only legal to run with lowbeams in low visibility situations.
The Truck-Lite LED floodlights (small ones on bumper) were wired per the diagram above to a switch by the driver's side speaker. Simple on/off lighted switch using a running light t-tap to trip the relay.
Offroad use only.
The Truck-Lite LED spotlights (the big suckers) were wired with a harness that I asked Rallylights to build to use the driver's side OE H13 plug's highbeam circuit to trip the relay; the rest of the wiring is per the diagram.
These would only come on with the highbeams when the switch was thrown.
Almost legal to run with highbeams, not legal with lowbeams, and great for offroad.
I never got around to A-pillar lights or anything on the roof. Before I'd think of that I'd install something to help while backing up.
|06-21-2011 09:51 AM|
|mrMangoTango||can i use the battery to power the switch? in that case it would turn on even when the car is off which is fine, but would it drain my battery?|
|06-20-2011 08:35 AM|
A Cibie headlight upgrade from Daniel Stern is even better money spent...
Welcome to the forum.
There are some great old threads that will give you some ideas too. Don't spend money 'til you check the archive of wisdom found in these pages.
|06-20-2011 08:19 AM|
2011 sahara windshield light mount questions
Im new to wranglers, this being my first one, and i need help with wiring the switch for my new driving lights.
1) Do i need a relay?
2) Where do i put the switch inside of the cabin?
3) Where can i run the wires from engine compartment into the cabin?
Thanks in advance for the help.
Pictures would be very helpful as well