Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Resetting maintenance indicator light after changing O2 sensors?

Join Wrangler Forum Today


Thread: Resetting maintenance indicator light after changing O2 sensors? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-16-2007 07:52 PM
92jeepster48195 The "Maintenance Required" light just went on my '92 Wrangler at 82,500 miles and according to the maintenace schedule it's time to change my oxygen sensor. Well, the Jeep is running just fine so how do I turn the warning light off? I disconnected the negative cable on the battery for about 30 minutes and it still stays on. Any suggestions? Thanks!
11-08-2006 12:15 AM
Swizz Auto Zone will do it for you too but in NY (at least my location) were not "supposed" to do it I have no idea why but we gotta do it on the down low cause we get the 5th degree for clearin codes.

I always do it anyway =) never had a problem............
10-20-2006 09:26 PM
04tjinsa Like Jerry said just discconect the battery for a minute or two. This works on my sons 96 dodge ram.
10-18-2006 01:04 AM
ironmonk
Thanks

It turns out the Haynes manual is out-dated, even though it is supposed to cover models up to 2003. What it said only applies to OBD I. 1998 TJ uses OBD II, so no such indicator light. Which also explains why FSM did not mention it.

Thanks.
10-17-2006 04:44 PM
Jerry Bransford To reset the ECU and any existing Check Engine light, all you have to do is disconnect the battery for 1-2 minutes. No need to go elsewhere and have someone use any special tool.
10-17-2006 11:05 AM
khenderson you can also do this and it'll take care of the light.

ECU reset
10-17-2006 07:04 AM
jeeperman If you end up with a "check engine" light or the like, you can go to autozone and they will reset as a rule...
10-17-2006 01:17 AM
ironmonk
Resetting maintenance indicator light after changing O2 sensors?

Hi:

I am going to change the O2 sensors on my 1998 TJ Wrangler Sport (6 cylinder, 4.0L). According to the Haynes manual, I need to reset the emissions maintenance indicator light. Here is the paragraph from Haynes manual:

"On 1991 and later models, the emissions maintenance indicator light can only be reset with a special tool available at most auto parts stores. After replacing the oxygen sensor, take the vehicle to a dealer service department or other properly equipped repair facility and have the light reset."

I looked up the factory service manual, and it did not mention any such indicator light. I wonder if anyone has heard such a light?

Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:51 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC