Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Mopar side step installation

Join Wrangler Forum Today


Thread: Mopar side step installation Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-07-2007 09:04 PM
TeeJay let's see the new shin guards!
11-07-2007 09:02 PM
sgarelick WOW, those were really hard to fish through. After playing for more than an hour, I finally was able to get all the bolts in.

Thanks for all your help.

--Steve
11-07-2007 08:25 PM
TeeJay start by passing it through the slit turned kind of sideways. it wont fit in both at once

0......0
...l...l....

Start side ways in the second 'l' and fish the other end through the first '0'
then grab that end and use it to pull the remaining portion the rest of the way through that second 'l' you started in and up until it can be finagled through the second '0'

put on the rest of the stuff.
11-07-2007 08:00 PM
sgarelick Not sure I understand TeeJay. There are 2 hole on top and 2 slits below them (see picture above). The bolts do not fit into the bottom slits. They do fit into the 2 holes, but no matter how I try, I can't seem to fish the other end around and through the holes.

Sorry if I'm slow on this, I'm just not getting it.
11-07-2007 07:47 PM
TeeJay put the short side in the long slit on the lower rear section. Finagle the thread through the hole in the front. grab the short thread and use it to fish the long end through the rear hole and place the small threaded washers on so as not to drop the silly little piece.
11-07-2007 07:22 PM
4point Put a washer and a nut on the long side so you don't drop the bolt into the frame,insert the short side of the bolt into the first frame hole and push it over and out the other frame hole. Mind you I've never installed these so I'm guessing from your illustration.
11-07-2007 07:16 PM
sgarelick tried that and played around for a while to get the long side to come out the other whole but I just can't get it. There must be something I'm doing wrong.
11-07-2007 07:12 PM
4point It looks like you should stick the short side through first.
11-07-2007 07:08 PM
sgarelick Attachment 2801

here's a scan of the instructions.
11-07-2007 06:57 PM
sgarelick Here are some pictures (as long as I posted them correctly)

Attachment 2799

Attachment 2800
11-07-2007 06:41 PM
sgarelick
Mopar side step installation

OK, I can't figure this out. I bought a pair of Mopar side steps for my 2004 Wrangler. It can with bolts that are shaped like this (one threaded end is longer than the other):

|
|
| |
|________________ |


I see the 2 holes that the bolt is supposed to go into but can't figure out how to thread it through the holes. You somehow have to put one end in first and then fish it around so that the other end comes out the other whole. I wish I could describe this better but those of you who have installed them must know what I'm talking about.

Any thoughts on how to do this. The installation instructions make it look simple but don't say if you stick the short end in first or the long end.

--Steve

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:41 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC