Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > slight tranny vibration

Join Wrangler Forum Today


Thread: slight tranny vibration Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-05-2006 06:10 AM
3jeepguy ditto sye is the answer
07-04-2006 08:59 PM
jeeperman Most U-joints won't last very long running more than 20 degrees (that is the maximum recommended by the manufacturers anyways...) You will probably be stuck with some vibrations until you get a CV shaft and a SYE kit in the rear as suggested above. Are the angles at both u-joints the same at both ends? (Axle and t-case) If not, that will give you vibrations as well. Typically with a SOA conversion you get at least 5.5" of lift, and with that much lift, I don't think that you are going to completely get rid of your vibrations unless you go with a SYE kit.
07-04-2006 06:14 PM
raysnutt18 http://www.jeepforum.com/gallery/fil...veshaft003.jpg

this is the pix of the driveshaft.......it has the washers on the skid plate and on top of the tc so I know it was lowered...some. doing the measuring... the driveshaft is 25 degrees+/-
07-04-2006 01:42 PM
mrbigjeep jus playin earlier but if u got a lil vibration u can always drop the skid plate with washers...ur thing says u got a spring over so i doubt that u have the skid plate dropped so u can always get a transfer case lowering kit...but like bluvikng said, the sye and new driveshaft will be more expensive...but definitely the best
07-04-2006 12:47 PM
bluvikng More than likely your vibration is coming from your driveshaft. If you still have the slip yoke style, it is most probable. Did you drop your skid plate any, with the lift? If not, you probably need too. Or you can go with the SYE kit, and get a longer rear drive shaft. It is the more expensive fix, but in the long run, the best. If you have an auto tranny, you may want to go with a double cardon type yoke, at the t-case.
07-04-2006 11:28 AM
mrbigjeep well if its just slight then everything could be ok
07-04-2006 07:50 AM
raysnutt18
slight tranny vibration

Just had a lift put on my jeep and since then I have a slight tranny vibration when I start from a dead stop and I can feel it when my foot is in the gass...when coasting no vibration.....any thoughts?

4"RE spring-over/ 33x12.5 bfg at/ta

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:25 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC