Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > A/C and Heater - What Else to Check?

Join Wrangler Forum Today


Thread: A/C and Heater - What Else to Check? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-03-2011 05:57 AM
Rubicondon53 My factory rotary switch for a/c went out years ago. I bypassed it, and installed an on\off toggle... If that blame stupid rotary goes out completely, I'll continue to tap into the harness and install toggles as I go.. Those rotarys are unreliable, and I'm sure they will all be dummy switches as they will continue to fail..
11-03-2011 12:04 AM
scottunzicker No? Anything?
11-02-2011 04:41 PM
scottunzicker
A/C and Heater - What Else to Check?

So here's what's going on: Neither my A/C nor my heater will kick in when I turn the hot/cold knob on the control unit. I know for a fact that my fan switch is out, too, but I can jumper the contacts in the plug to make the fan come on.

With winter coming on, I'm mostly concerned about getting some heat going. I've checked the heater blower motor by hooking up 12v to it, and it worked fine (I also put 12v across the A/C compressor clutch, and it worked fine, too). The blend door actuator motor WAS seized up, but I cleaned it, hooked up 12v to it, and it's working fine directly connected to the battery. HOWEVER, when I plugged it back into its harness and rotated the hot/cold knob, the actuator didn't move. I then MANUALLY rotated the blend door all the way both left and right with the fan blowing, but could feel no hot air coming from any of the various vent settings I tried (the vent selector knob seems fine - I select floor, and air blows out the floor vent, dash vent, etc.). Looking at the A/C heater control unit from the front (fan switch, hot/cold knob, vent selector), there are three wires on the far right side. The top one is green, the other two are black. It doesn't seem to matter which order the bottom two are in when I try everything.

Here's what I'm going to try first. Since the fan speed switch is messed up, its connector pretty much melted, the hot/cold knob doesn't seem to work, and the vent selector knob is getting crusty, I'm going to go pick up a new A/C / Heater control unit from AutoZone, splice it in, and see what happens.

Any and all guidance, tips, troubleshooting steps, etc., appreciated.

Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:59 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC