Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Getting rid of rough idle

Join Wrangler Forum Today


Thread: Getting rid of rough idle Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-04-2011 12:17 PM
Garyk Also look for a vacuum leak especially at the TB.
11-04-2011 09:35 AM
RSC17 Thanks for the help Jerricho! I will break into it as soon as I have some time.
11-04-2011 09:26 AM
Jerricho Does it sound like you have one cylinder that is not firing? A lot of times a rough idle will be caused by one cylinder that does not fire until you hit a certain RPM say 1200. Every time that piston comes around when the next one in line fires it hits pretty hard because the bad one didn't fire and allowed the engine speed to drop.

It looks like you have already started on the 2 most common causes if that is it, the one I have seen the most is the gap on one of the plugs is to wide. At low rpm there is not quite enough power to jump the gap, but once the rpm's speed up you get enough power to make the jump and it starts firing. You can re-gap them all or figure out which one is doing it and just re-gap that one.

The other one you have already started is if one of your injectors can be slightly clogged, at idle not enough fuel is getting through, but when you increase the pressure you get some fuel through(though still not as much as you should). You could clean/replace the bad injector.

If it is the cylinder thing it is pretty easy to figure out, just pull a plug wire off a plug enough for it to not spark and start the jeep, if it sounds even worse or wont run at all then you will know that it isn't that one. One of them will make the jeep idle exactly the same weather it is hooked up or not, that is your culprit.
11-04-2011 08:28 AM
RSC17 Sorry about that... 95 YJ -4cyl

No have not done compression leakdown. Oil is fine when I change it though so i'm going to put that at the bottom of my list of reasons. I think...
11-03-2011 08:22 PM
P0234 Did you test compression/leakdown? Mine has a blown headgasket and is very rough at idle. Smooth past 1500rpm.
11-03-2011 08:10 PM
jfbilbro what year??...what motor?
11-03-2011 06:20 PM
RSC17
Getting rid of rough idle

The Jeep runs well just the idle is ROUGH as hell. Shakes the whole Jeep, the doors are noisy, etc. Seems if I could raise the idle just a tad it would solve everything. Is there any way to adjust the idle speed? If not, where should I start to try and improve the idle?

What I've done: new plugs, new wires, new cap and rotor, couple bottles of injector cleaner (one hell of a desperate attempt)

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:32 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC