Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > help 19v on instrument cluster

Join Wrangler Forum Today


Thread: help 19v on instrument cluster Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-30-2011 12:22 PM
obidya you guys with the 19v spike... you may also want to check your voltage regulator. You should not be seeing a spike that high. It sounds like you got it locked down and figured out, but me personally... I would still double check the regulator.
07-11-2010 09:17 PM
KenJohnson It looks like compshooter is correct.

I experienced the same intermittent 19 Volt reading on the voltmeter in my daughter's 2000 4.0L. A few times I pulled over, jumped out, and measured the voltage at the battery with a digital voltmeter with the engine running. Reading ~13.6 Volts. Seemed a bit low, but perhaps that's where it sits. I don't yet have much experience with the vehicle.

I cleaned and tightened the negative battery post after reading this thread and also followed the ground down to the upper mounting bolt of the starter motor on the bell housing side of the starter. The bolt was loose. After tightening the bolt the battery reading went to ~14.5 Volts (running) and the 19V behavior has thus far not reoccurred.

Perhaps I should have thought about it. I replaced the clutch six days before the problem started. The loose bolt either hadn't been tightened correctly or it had vibrated loose. I suspect the former to be honest.

At any rate, I joined the forum to offer confirmation and say thanks for the solution.
10-11-2007 11:58 AM
compshooter It's the ground side of your battery. Check and make sure the cable is tight to the battery post on the negative side. Hell, check the positive side too while you're in there. If the negative side is tight, then trace the cable down to where it grounds to the frame. My bet is that it is loose on the frame (or wherever the end of the ground cable goes).
10-10-2007 04:20 PM
jroe
help 19v on instrument cluster

hello everybody. Im new. so hello and i hope you guys can help. ive done alot of searching for this. I found a few things that im going to do or try. My problem is my jeep wont start. i jumped it and it would run for a few seconds then die. I pushed started it and drove it around a parking lot and now i runs fine. when i went to drive it home my volt meter on the instrument cluster red 19 v and gauge waring light came on infoing me on the battery meter high volts. and then just as i was looking at it the warning went away and the volts went back down to 14 volts normal. then a few miles down the road same thing then back to normal. Now i say battery cables battery is good 12.38v when trying to crank, but only clicking is happening. Battery cables have never been changed. Ive read possiblities, starter soloniod, starter, even possible altinator. i went to check the connections on the altinator red wire which bolts straight to the altinator was good, but the plug that attaches to the back of the altinator was alittle melted on the inside where the prongs are. so what do you guys think? by the way the jeep is a 2000 model 4.0L
Oh and the alarm is very tempermental on this and i have already sortive ruled it out on this problem, but i would like to remove the alarm, it looks factory alarm, so does anybody now how to remove it completely?
thanks so much for your help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:44 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC