Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > BA/10 Peaugot to AX15 linkage?

Join Wrangler Forum Today


Thread: BA/10 Peaugot to AX15 linkage? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-10-2012 09:00 PM
bigskycountry0329 Scott, no I did not have to change the output shaft. the bell housing I used came with my new AX15 (the BA10 bell housing will not bolt to the AX15 and I also recieved a new clutch with my find. iu saved my old clutch that was with the BA10 because it will work fine when I need another.
01-16-2012 05:56 PM
scott howard did you not have to change the out put shaft of the trans? and the bell housing and clutch ?
if my ba10 ever goes out i want to do the same exchange
01-16-2012 10:21 AM
bigskycountry0329 Thanks Matcheen. I swapped out the T-Case with one from the same 1998 TJ that the AX15 came from. On the BA10 the 4x4 linkage mounts to the T-case in 2 places and one spot on the BA10, but with the AX15 application the linkage mounts to one place on the T-case and 2 places on the tranny. It looks like I will have to modify one mount eye on the linkage and I will be good.
01-08-2012 08:40 PM
Matcheen Isn't the 4X4 linkage on the T-case? Are you swapping that too? It should work though.

The shifter config should be the same, the NP 231 doesn't see the small push to the side that you need to do with the YJ shifter Vs. the straigh up pull from the TJ, it's all the same motion to the T-case.

Put the NP 231 from the BA onto the AX15, if it's the NP231 AMG there will be one less bolt than the NP231 JP
but it will fit.

I hope I understood/answered your question.
01-08-2012 08:15 PM
bigskycountry0329
BA/10 Peaugot to AX15 linkage?

I am in the middle of swapping out my dead BA/10-5 Peaugot transmission to the old faithful AX15. The 4x4 shifter linkage that was on the Peaugot will not work for the AX15. The AX15 is from a 1998 TJ. I do not think the 4x4 linkage will work from a TJ. The TJ linkage has a lever in the cab while my 1990 YJ has what looks more like a shifter. Does anyone have any sugestions?

I am running a 1990 YJ with a 4.0 FI from a 1992 Cherokee.

Thanks everyone.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:23 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC