Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Another clutch problem

Join Wrangler Forum Today


Thread: Another clutch problem Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-14-2012 06:03 PM
YJPunisher213 Slave cylinder slides over the main shaft that goes into the engine. The slave moves the throw out bearing until the high-friction material on the transmission's clutch disengages from the engine's flywheel.
01-13-2012 09:10 PM
jakethejake also, again, bear with me on the car clutch questions. where is the slave cylinder at? I assume near the back of the tranny? (and for someone with a whole MESS of patience...what does the slave do, and vs the master cylinder?
01-13-2012 09:06 PM
jakethejake OK, so if there WERE to be a leak somehow....where are some common areas the ax-5 can leak from?

Also, it did seem to start really feeling the most noticeably light was right after i sprayed the motor off after taking it in some nasty mud last weekend.

Also.....i went nose first into a hole in the trail that had about 2" of ice on top, and it stalled the jeep. I basically plowed into a hole a total of probably 3-4' deep: 1-2 in really soft but thick mud and then another 2' of water, with the ice on top. is it possible something could have gotten knocked loose by the plunge, and then finally gave out the night i sprayed everything down?
01-13-2012 05:56 PM
rogerf1970 what makes you think you need to bleed your system.. a working hydraulic system does not need bleeding unless you have a leak. never the less
If your slave is inside the bell housing then you will have a metal hydraulic line going in and 1 coming out, the 1 coming out will have a bleeder on the end.. below is a pic that should be close to what your looking for...

my process of bleeding a clutch is... fill master, pump for a min, hold,bleed,pump,hold,bleed,FILL Master... repeat..

Attachment 89591
01-13-2012 04:16 PM
Jeffro Martin Jackson get some fluid n go top it off n pump the heck outa it. might get some sign of life after like 100 pumps.
01-13-2012 04:11 PM
jakethejake sonofabeach. Its sitting in the parking lot at work, 20 min drive back home to the warm garage-Through downtown traffic, with no clutch.
01-13-2012 04:06 PM
Jeffro Martin Jackson yea ur slaves internal. Maybe someone with knowledge of your setup will come along. Mines external.....damn dude that sucks....something SO simple is turned into a project....I think your have to remove your tranny but dont take my word for it.
01-13-2012 03:59 PM
jakethejake Yea, im with ya on that but there's no bleeder screw anywhere but in the damn bell?
01-13-2012 03:56 PM
Jeffro Martin Jackson same as breaks....but i think your slave cyclinder is actually inside of the bellhousing so idno how much a pain in the ass it will be.....but basically you would fill resivor n pump clutch ...then release the pressure on the slave cylinder. Repeat till fluid comes out of slave. Keep eye on resivor and keep topping it off. youll actually feel when cluch is being engaved through the pedal then i would repaet process another time or two to make sure line is full n no air in it.
01-13-2012 02:43 PM
jakethejake
Another clutch problem

Hey guys recently (and finally) purchased a 92 YJ S. 2.5 I4 5spd. Great shape, just a few miscellaneous problems here and there. I have done some searching and im thinking I need to just bleed the system. This is MY first standard shift vehicle. Been riding motorcycles and dirt bikes my whole life. No idea how a hydro clutch works. I assume its identical to bleeding brakes, but I dont have damn clue as to where the bleeder is on the jeep. Any help finding it would be awesome. I have pretty solid mech. skills, just not much when it comes to car clutches.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:36 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC