|03-30-2012 11:10 AM|
By that I mean to actually cut about 1/2" to 3/4" off the outside of the spring bucket (seat). It will not affect the spring and will give your tire sidewall something (the spring) to rub on that will not cut it.
The cut should be a straight cut parallel with the tire sidewall. Make the edges smooth and with nothing sharp left to make the work hard on the tire.
Most times you won't need any spacers by doing this.
If you do use the spacers... make sure to use a torque wrench any time you mount or dismount them or the tires/wheels. A little lock tite on the spacer is a good idea as well.
|03-30-2012 09:39 AM|
|03-30-2012 06:25 AM|
lot's of folks think spacers are just another cool mod that only costs 200 bucks. When in fact, or should I say, IMHO, they are a bit of a bandaid solution to fix rubbing issues.
The further you bump your wheels out, the more stress you have on bearings & steering components. Some on here do it sorely for looks. I'm not a fan of the "Scateboard" look. That being said, if your backspacing is 6" w/o spacers and you rub, then you add your 1.5 spacers which brings you to 4.5". There will be no more stress on your jeep with the spacers vs a new set of wheels that have a 4.5 BS.
I'm not a big fan of spacers, however I ran 1.5's until I could afford new wheels with the proper BS. Ran em for over a year w/o a single problem.
If you get them I would get hubcentric ones, propery lok tite & torque them down & buy the proper hub rings & installl them. I bought mine off of Amazon for 12 bucks.
Hope this helps!
|03-30-2012 04:14 AM|
|BroderickMi||I'm wondering if that just too close when flexing offroad|
|03-30-2012 01:40 AM|
|Conquest||Thanks for the info. Already did the steering stop washer fix. Sounds like i'm good to go now!|
|03-30-2012 12:40 AM|
|Jerry Bransford||Jeep Steer Stop Adjustment|
|03-29-2012 11:59 PM|
|03-29-2012 11:49 PM|
|Conquest||Follow up--I actually have 4.5 inch of BS.|
|03-29-2012 10:54 PM|
Thanks for the comments--tonight i'll check the actual BS, I'm certain it's at least 4 inch's might be 4.25 though.
I am running 16x9's and don't have any issues up front after I added two washer to the steering stops.
I'm running flat 6" BW flares which cover all the tread so I don't get much if any water/mud etc--which is great. But with only a half inch between the rear coils and tire I'm wondering if that just too close when flexing offroad.
|03-29-2012 08:11 PM|
If your wheels truly have 4" of backspacing and they are 15x8, that is absolutely perfect for 35x12.50 tires. Use no spacers for that combination!
And being hub-centric or not has absolutely no effect on any of this. The factory wheels are hub-centric, very few aftermarket wheels are and it really doesn't affect anything.
The below illustrates how backspacing is measured... the yellow tape measure is measuring the wheel's backspacing... the distance from the inner-most edge of the wheel to the wheel's mounting flange.
|03-29-2012 08:07 PM|
|Mudweiser||I put a set of 1.5" spidertrax on mine due to the 33x12.50s having no clearance on stock rims. Was a cheaper fix then having to buy the new rims right away. No problems with them at all. But like said above....dont go cheap with them, or you will regret it.|
|03-29-2012 07:58 PM|
|cubalz||Seems to me that hubcentric spacers are only really necessary when using stock rims that are hubcentric. Most aftermarket rims are not hubcentric so it makes HC spacers unnecessary. I may be wrong...|
|03-29-2012 07:04 PM|
If your going to run spacers make sure you get hub-centric, like these spydertrax.
I have had spydertrax on my JK for about 30,000 miles and have not had a single issue, on road, offroad...nothing.
|03-29-2012 06:56 PM|
|6InARowMakesItGo||1/2" is close but i'd be more worried about it in the front. personally i would change wheels before installing spacers.|
|03-29-2012 04:09 PM|
Are wheel spacers right for me
Need a little advise. I'm running 35's with rims i really like but the backspacing is around 4". I have not done much offroading yet as i've been building up the jeep. Looking at the distance between the the rear spring and my new 35" side wall, I only have about 1/2 inch of clearance. Do I need wheel spacers to keep from tearing up my tires?