Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > t-case angle, XJ double joints driveshaft ??

Join Wrangler Forum Today


Thread: t-case angle, XJ double joints driveshaft ?? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-12-2006 09:38 AM
socalchef pick up another cherokee front shaft and have your driveshaft guy cut it down to fit. I run them front and rear. You'll need the slip yoke eliminator on the tcase. Using the CV joint AND a slip yoke won't really work all that swell. To use one in the front you'll also need a CV compatible yoke (takes bolts through the back into the driveshaft rather then ubolts or straps. i wouldn't worry so much about the angle at which you place the tcase output. when running a CV driveshaft, you set the pinion on the axle to point 1-3 degrees below the tcase output. with the slip yoke eliminator on the transfer case and the slightly longer with CV shaft, you won't have vibes at 4". For building the rear crossmember to hold the transfer case, just raise it as high as you can and build it there.
09-11-2006 10:50 AM
73mach1
t-case angle, XJ double joints driveshaft ??

heres the situation.... i have a YJ frame, cj7 fiber body, amc 304 engine, XJ ax-15 tranny, XJ np231 t-case, since there wasnt any v8 in yjs i made a 1/4inch shim between the engine and tranny, machined the pilot bearing along with other minor mods, so the 304 is now in the frame, i made the front custom engine mounts, now time to make the rear one, it will be a custom crossmember for the t-case support along with a custom skidplate, since i will put a 4inch suspensin lift (and if the yj was stock) i would need the lower the t-case, since mine is custom i can put it right where it should go... so questions are :

i bought a 93 cherokee for the tranny but also have the front driveshat wich is a double joint , could it fit the rear of the yj since its shorter ? where i work we have a driveshaft guy wich should be able to weld me the double yoke to the stock driveshaft then make a slipyoke in it and balanced so modification isnt a problem just want to know if it would be good, i dont want vibes

since i dont have the 4inch lift now the only way i can measure where the t-case must be bolted is the angle of the t-case or tranny, i measured the t-case angle on my father XJ and found 6 degree so i assume that running the engine/tranny/t-case at 10 degree would be correct ??

yan

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:47 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC