Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Anyone know how the brights attach to the wiper switch?

Join Wrangler Forum Today


Thread: Anyone know how the brights attach to the wiper switch? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-04-2012 11:43 AM
MoabManN Did you find a picture of this? I've got the same problem
02-12-2011 08:57 PM
Jarrodbeckstead
Quote:
Originally Posted by NHrubicon
On my 94 YJ the headlights are controlled by 'rocker' switches on the lower left hand corner of the dashboard...under the guage cluster...and the high beam 'clicker' is on the turn signal switch-you pull 'forward' to click it. On my 03 rubicon TJ, everything is controlled on the turnsignal stem, nothing on the dash.
That's what I was asking about... There's a rod like hanger wire that runs along the steering column and has a 90 degree bend at the end and sits right behind the wiper switch. I just need to know how it hooks into the multifunction lever.
02-12-2011 09:54 AM
HyperBuzzin
Quote:
Originally Posted by InfernoGirl View Post
Well on the pre 2000 TJ's there's a knob on the dash, but I just thought maybe he was trying to install it on the wrong arm....
Maybe the Jeep's from England, where everythings on the wrong side??
02-10-2011 02:53 PM
NHrubicon On my 94 YJ the headlights are controlled by 'rocker' switches on the lower left hand corner of the dashboard...under the guage cluster...and the high beam 'clicker' is on the turn signal switch-you pull 'forward' to click it. On my 03 rubicon TJ, everything is controlled on the turnsignal stem, nothing on the dash.
02-10-2011 02:35 PM
Hardermods Wiper Switch
1 Disconnect battery ground cable.
2 Remove turn signal switch, refer to Vehicle Lighting/Turn Signals/Turn Signal Switch/Service and Repair
3 Remove ignition lock
4 Remove column-to-instrument panel mounting nuts, then disconnect wiper switch electrical connector.
5 Remove column mounting bracket-to-column attaching bolts, then the bracket and allow column to drop down.
6 Remove ignition and dimmer switches

Turn Signal Switch
1. Disconnect battery ground cable.
2. Remove steering wheel, refer to Steering and Suspension/Steering/Steering Wheel/Service and Repair .
3. Using suitable tool, remove cover from lock plate, then remove lock plate as follows:
1. Identify steering shaft thread type. Metric shafts have an identifying groove on steering wheel locating splines as shown.
2. Mount lock plate compressor tool No. J-23653 or equivalent on steering shaft, using forcing bolt tool No. J-23653-A on models with metric steering shafts.
3. Tighten nut on tool to compress upper bearing preload spring, then remove and discard lock plate retaining ring.
4. Loosen nut on tool, then remove tool and lock plate.

4. Remove turn signal canceling cam, upper bearing preload spring and thrust washer from steering shaft.
5. Move turn signal actuating lever in right turn position and remove lever.
6. Remove hazard warning switch button from steering column.
7. Remove turn signal electrical connector harness from column mounting bracket and disconnect connector.
8. Remove turn signal switch attaching screws, then pull switch and electrical connector harness from steering column.
9. Reverse procedure to install.

I copied this out of the factory service manual but it has no other info on the dimmer switches
02-10-2011 01:30 PM
InfernoGirl Well on the pre 2000 TJ's there's a knob on the dash, but I just thought maybe he was trying to install it on the wrong arm....
02-10-2011 12:18 PM
Dogzilla In all likelyhood, it's that way on the YJ too.
02-10-2011 09:16 AM
InfernoGirl Well Idk about YJ's, but on TJ's the bright switch is on the turn signal arm, not the wiper arm....
02-10-2011 12:42 AM
Jarrodbeckstead
Anyone know how the brights attach to the wiper switch?

Well I just replace my wiper switch because my jeep seemed to lack one, haha, but I cant figure out how the high beams are supposed to connect to the multifunction stick thing. Ya, I just said that. I've got a 92' YJ if anyone can maybe take a pic or walk me through it because I wasted my money on the autozone brand owners manual that is about as informative as toilet paper. Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:03 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC