Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Bad rumble in my 92 YJ

Join Wrangler Forum Today

Thread: Bad rumble in my 92 YJ Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-25-2012 11:52 PM
Spooky52 Thanks, I'll give it a peek. I'm hoping it is something simple but with my luck, I doubt it. Jim
08-25-2012 11:29 PM
jokerchief462 Take a look here and do some for pinion angle. In fact go to Tom Wood's Custom Drive Shafts - Tom Woods Custom Drive Shafts Custom Driveshafts Specialist and on the web page look for technical information. It has a few pages on driveshaft ceometry and it will explain everything and answer all the questions. Then you can look at yours again and see if that might be the problem and save you some $$$$.
08-25-2012 05:49 PM
Spooky52 Yep, I put a whole new NAPA clutch kit, complete with pilot, pressure plate and throwout bearing in and even had the flywheel worked. I don't think the pinion angle is bad. I checked with the spring factory to make sure that the wedge that they put on to correct pinion angle was facing the right way. These were, I thought, direct replacement springs but they turned out to have about 2 1/2" of lift. Not a great deal of lift but a bear to get into place. I changed the springs because the original springs were flat across because of the winch and hard top. It's always something. I'm guessing that I'll end up taking it to the dealer and getting it fixed and getting screwed at the same time. :-)
08-25-2012 02:38 PM
jokerchief462 When you put in the clutch did you replace the pilot bearing? Has it been greased before the tranny went in? Also a lift kit is the pinion angle still good. All things to look at.
08-25-2012 02:10 PM
Bad rumble in my 92 YJ

I just put a new set of springs on my 92 YJ (I won't do THAT again) and now it has a REALLY bad rumble in the lower three gears and it lessens in 4th and 5th. If you push the clutch in the rumble goes away. I put it up on jack stands and ran it in gear but couldn't find the source. It sounds and shakes like I'm driving down the road with knobby tires on. The new springs raised the Jeep about 2 1/2" but I don't think that is the problem as the rumble was there before but barely noticeable. Anyone have any suggestions as to where to look? The rumble started after I replaced the clutch a few months ago (won't do THAT again either). I'm wary of driving it too much as something might turn loose before I can get it fixed. Any help would be appreciated. Thanks. Jim

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 07:37 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC