|09-17-2013 03:20 PM|
FYI people we aware tanks without dimples are bad news.
The lack of dimple on this particular skid plate cause the ring on top of the tank to pop and allow all kinds of garbage into my tank eventually clogging the fuel pump and leaving me stranded on the side of the road.
I suggest finding a better skid and avoiding extreme metal products, this design flaw is unforgivable.
|09-14-2012 08:20 PM|
|Unlimited05||that looks real nice. im gona look into it cause i was gona do a 1in. BL and a tummy tuck.|
|09-12-2012 07:22 PM|
I bought this one from Extreme Metal Products
I got mine from them via eBay:
Here is their website:
a touch beefier than stock lol
|09-12-2012 05:37 PM|
|Unlimited05||which one did u get?|
|09-12-2012 01:56 PM|
the skid I bought worked great!
you would not need a body lift to use it, it raises the tank but not higher than the stock mounting point which is still a good ways under the tub.
I would recommend the one i bought, it fit perfect, held the tank nice and snug using the stock straps. the Welds were really nice, and it had a good thick powder coat so it should last a nice long time. Im very happy with it
|09-05-2012 01:06 PM|
I dont believe so ... but
Most of the skid plates I've researched say they don't, some say they do on the rubicon, I can take some measurements old and new on mine to see how much room is actually allowed and post them up here. I do have a 2" BL so if theres less than 2" clearance we'll know it wont work
|09-05-2012 12:04 PM|
|Unlimited05||do u have to do a body lift to lift the tank??|
|09-05-2012 10:59 AM|
Old Skid Plate...
|08-30-2012 06:13 PM|
On the bright side...
The skid plate about tore in half, which means I had to order a new one.
New skid plate, new straps, and new pump assembly on on the way.
can anyone say tummy tuck?
Jeep TJ/ Gas tank skid plate/ rock crawler/ Rubicon | eBay
Figured I would give this a shot, lift the tank an inch.
another plus: judging by how much it looked like the old regulator was leaking... my MPG should improve some
|08-30-2012 03:38 PM|
|div4gold||That's a bummer, off with the tank again pia. On the bright side at least now you get a new fuel filter.|
|08-30-2012 02:23 PM|
|obidya||the sending unit is clogged, and the pump couldn't handle it and is now also dead...|
|08-29-2012 04:52 PM|
|div4gold||Can you hear the pump cycle when you turn on the key?|
|08-29-2012 04:14 PM|
the flow is going the proper way (only one way it can be installed)
I did not replace the fuel filter, it is an internal non serviceable part.
I popped the pressure valve at the rail and only air came out, but nothing I did seemed to be able to get it started...
I do not have a fuel pressure gauge...
off to napa...
|08-29-2012 04:12 PM|
|Mom sold the Jeepster||See if the old one works, might be a bad replacement part|
|08-29-2012 03:51 PM|
|Blind Dog||Got air bubbles trapped in the line? Vacuum hose, if any, hooked up correctly? Is it adjustable and not set? Got a fuel pressure gauge?|
|08-29-2012 03:12 PM|
|div4gold||Did you replace the fuel filter when you did the regulator?|
|08-29-2012 03:07 PM|
|div4gold||I assume you have the flow going in the right direction?|
|08-29-2012 01:59 PM|
HELP: wont start
I just replaced my fuel pressure regulator and now it won't start.
When I first finished it started up ran rough for a few, then calmed down and ran fine. I shut it off and tried to start it up again and it burbled around at about 100 rpm sounding horrible, dyeing when I gave it throttle, now it wont start at all.
what are some possibilities?