Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Rattling noise in clutch / flywheel bell housing

Join Wrangler Forum Today

Thread: Rattling noise in clutch / flywheel bell housing Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-17-2012 04:21 PM
JeepJimNL 0III0forlife thank you again!
That's 2 of my posts you've replied to in one day
Time to do some shopping for parts I think.
09-16-2012 08:09 AM
0III0forlife Sounds to me like it is possibly one of the springs in the clutch itself.

I have had them come loose and fall down, only to get picked back up and flung up against the bell housing. Sounds kinda like that little kids fake lawn mower..pop,pop,

A clutch job is just basic mechanics skills. Its harder to put back together than to get apart.

You have to take both driveshafts off.
Then support the t-case tail shaft with a jack stand and take the skidplate off.
I always put a small bottle jack under the oil pan at this point, cause you will need it there for support as well as helping with alignment later.
Next you support the trans with your other jack stand, and unbolt and remove the t-case.
Then comes the fun part, disconecting the line for the hydraulic clutch, and unbolting the bell housing from the motor.
After all is loose its just brute force and lots of swear words and it will come out of there.

Get a clutch kit from NAPA or your favorite auto parts store. The kit will come with a clutch disc, pressure plate, throw out bearing, and a pilot shaft bushing.

Take out all of the old parts, replace with the new parts, and reverse the order of the tear down and you have just replaced your clutch.

I have done many, and i just replaced the clutch in my 87 Wrangler this summer while switching to an updated AX15 trans as well. The job took me approximately 6hrs, working alone. So for someone like yourself that has never done it before, figure on atleast a weekend or so.
09-16-2012 04:16 AM
Rattling noise in clutch / flywheel bell housing

Good morning all.

I have an '89 4.2 that has suddenly started making a strange noise in the bell housing behind the starter motor.

It sounds like a piece of loose metal that gets picked up by a moving part (probably the flywheel?) and rattled round. It's inconsistent (not constant) and it happens with the clutch in or out suggesting that it's forward of the gearbox.

It's also a 'dry' rattle which leads me to believe it's in the bell housing.

I've had the starter motor off - it's worn, but not missing any teeth.
Ditto the flywheel - it's all in one piece and not missing any teeth.

I get a slight knocking noise when in idle with the clutch out - have done since I got the jeep.

Do these symptoms sound familiar to anyone?

Is it new clutch time? And if so, how big a job is that?


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:03 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC