Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > CJ Jeep Forum > CJ General Discussion Forum > Disc Brakes

Join Wrangler Forum Today


Thread: Disc Brakes Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-07-2012 05:11 PM
jbhtn I found a Dana 30 front out of a '79 on CL for $250. It has discs and is supposed to be in good working order. Will these brakes switch over or should I consider swapping axles. Everyone's opinion is appreciated.
10-02-2012 07:03 PM
jbhtn Thanks, again for all of the info. I have started tearing the thing down and am trying to figure out whether I am going to keep the factory axles. I would like to get my hands on a set of Dana 44's which should spread the stance out a little bit, but if I am still going to have to convert to disc's I may just keep the factory axles.
10-01-2012 08:03 PM
fluff
Parts

Quote:
Originally Posted by jbhtn View Post
I have a '76 CJ 5 with stock axles. Are there any junk yard disc brakes that can be reasonibly fitted to replace the drums I have now.
If it is a dana 30 front, you will have to change the front hub assemble and the upper and lower ball joints to get your disc breaks. I will email you back with some phone numbers tomorrow. Fluff
10-01-2012 07:37 PM
fluff
Parts

Quote:
Originally Posted by jbhtn View Post
I have a '76 CJ 5 with stock axles. Are there any junk yard disc brakes that can be reasonibly fitted to replace the drums I have now.
Hi JBHTN, I am in Monterey, TN and I also just got done restoring my 76 CJ5. I am still hunting parts for my Jeep. Your disc breaks should be easy found. In this area there is quite a few parts available. If I can help you find the breaks parts, then let me know. Fluff
09-30-2012 07:42 PM
jbhtn Thanks for all the info., I didn't realize that 76's had any disc brakes. I will get on the hunt now.
09-30-2012 02:06 AM
hooper CJ Dana 30s


Early Dana 30s used a 11"x2" drum brake. Disk brakes were optional in 1976 and standard starting in 1977. Between '76-'78 the disk brakes used a large 10-1/2"x1-1/8" rotor. The "big brake" setup uses a 6 bolt caliper mounting bracket that goes between the knuckle and the spindle. The caliper is keyed to the mouting bracket and the rotor should apear wide when looking on edge. Rubber brake hoses with brass banjo fitting end. These rotors, calipers, and pads are compatible with the Scout II.
From 1979-1986 they used a 10-1/2"x7/8" rotor with a 2 bolt to knuckle caliper mounting bracket. From '79-'81 the caliper is keyed to the mounting bracket and uses rubber brake hoses with brass banjo fitting end. From '82-'86 the caliper is pin-bolted to the caliper bracket and the hoses are rubber crimped to steel line. All Dana 30s from 1972-1980 use a six bolt locking hub. From '72-'78 the factory had Warn Premium hubs as an option. From '79-'80 the factory used Warn non-premium hubs stock. From 1981-1986 they use a weak Warn five bolt locking hub stock. Jeeps built in the 70s with the Quadratrac transfer case will not have hubs at all unless they have been converted to part-time operation. They have driven plates instead. Hubs should not be used with this transfer case unless it has been converted to part-time operation.

Another big difference between the CJ and Dana 30s used in later models is the CJ has the diff case offset on the passenger side and the later models have the diff case offset on the drivers side.
Most CJ Dana 30s will have lock-outs on the hubs to engage or disengage the wheel from the axle. With both hubs unlocked, the axles, u-joints, differential, and front drive shaft do not spin. This is done to increase gas milage, and if a locker is installed in the front diff, it will impove handling on the pavement. Later model Dana 30s either an axle disconnect system or no disconnect system.
The CJ Dana 30 uses the 5 on 5.5" wheel bolt pattern other models use the 5 on 4.5" wheel bolt pattern.
Outer parts (knuckles out) can be switched amoung to different versions of the CJ Dana 30. This means CJs with drum brakes can upgrade to disk and CJs with cheesy 5 bolt locking hubs can upgrade to 6 bolt locking hubs. Later models use different knuckles and ball joints that are not compatible to the CJ Dana 30. Common gear ratios from '72-'75 were 3.73, from '76-'79 were 3.54, and from '80-'86 were 2.73

This is from jeep tech.com
09-30-2012 01:24 AM
hooper If you have a dana 30 it could be a easy swap.
09-30-2012 01:10 AM
hooper Being a 76 there should be alot of options since alot of 76's came with factory discs. Find out what axle you have first and go from there.
09-29-2012 10:33 PM
jbhtn
Disc Brakes

I have a '76 CJ 5 with stock axles. Are there any junk yard disc brakes that can be reasonibly fitted to replace the drums I have now.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:06 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC