Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > jeep tj driveshaft question!

Join Wrangler Forum Today


Thread: jeep tj driveshaft question! Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-16-2012 03:43 PM
Wh33lin
Quote:
Originally Posted by CanyonLakeTJ View Post
i was wondering if i can run 35s on a stock drive shaft for a while until i have the money for a slip yoke eliminator kit.

i have already up graded the axles dana 44 rear and dana 30 front ( chromoly axle shafts ) and re geared to 4:56 and about to buy a 4 inch lift with a already 1.25 body lift. i just want to know if i can run stock drive shaft with a t case drop kit for just a little while until i have money for the kit
I've been running for months a 4" skyjacker lift with the drop bracket, stock axles, gears, drive shafts, even rear w/o a SYE, with 35" Cepeks. No issues. I don't wheel hard, but I definitely put it to the test. Oh, and not body lift. No rubbing. All good so far.
11-09-2012 06:48 PM
CanyonLakeTJ thank you
11-09-2012 02:29 PM
Jerry Bransford You may not be able to get enough of an angle reduction with just a t-case drop to eliminate the vibes from a 4" suspension lift. You'll probably need to add a 1" motor mount to that t-case drop so the vibrations can be eliminated. At least not with a normal 1" t-case drop. If you can get rid of the vibes, you can continue using the OE rear driveshaft (the front is fine) but caution that the OE driveshaft is barely long enough to stay seated on the slip-joint t-case output shaft once the suspension lift is that tall. Some trail conditions might pull the front of the rear driveshaft off the t-case output shaft. Worse, such trail conditions might not completely pull it off where it can cock at an angle and jam on the t-case output shaft, bending the t-case output shaft.

Just be wary.
11-09-2012 02:22 PM
CanyonLakeTJ
jeep tj driveshaft question!

i was wondering if i can run 35s on a stock drive shaft for a while until i have the money for a slip yoke eliminator kit.

i have already up graded the axles dana 44 rear and dana 30 front ( chromoly axle shafts ) and re geared to 4:56 and about to buy a 4 inch lift with a already 1.25 body lift. i just want to know if i can run stock drive shaft with a t case drop kit for just a little while until i have money for the kit

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:41 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC