Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > General Jeep Discussion > Creating your own NutSert Installation tool for about $2 in any size

Join Wrangler Forum Today


Thread: Creating your own NutSert Installation tool for about $2 in any size Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-28-2012 07:17 PM
1SAS richsipe,

Great article!! Thanks for letting us know.

Take care,
11-27-2012 11:01 PM
richsipe Yep. I didn't have any problems with the grade 8 but the fasteners were stainless and learned about the anti seize quickly the hard way when I put those in.
11-27-2012 10:05 PM
redrockerfan
Quote:
Originally Posted by richsipe View Post
Creating your own NutSert Installation tool for about $2 in any size

Recently I was installing some Crusher Corners from Poison Spyder Customs and one of the rear installation bolts needed either a nutsert or a large hole cut into the tub. I chose the nutsert method as I didn't want a huge hole in the tub but realized that in the large size of the installation bolt I had no way of setting the nutsert.

Luckily I also had the installation kit for the TrailGate which included a provided nutsert kit for both of the sizes of nutserts that were included in that kit but unluckily it wasn't the right size.



After a quick look it seemed like a pretty simple construction:



After a trip to our local True Value hardware store I had the parts to build my own which ended up working pretty well.

The parts to build your own are:
1) Grade 8 half treaded bolt that fits in the nutsert. For mine it was a course thread which surprised me.
2) 2 Washers that fit the bolt. Try to get these as close fitting as you can. Mine was a bit loose and although it worked, it marred the surface of the nutsert a bit.
3) A Coupler that is larger than the bolt that allows the bot to fit through. This will be your holding spot with a large wrench to push down the nutsert onto.



Once you put it together it should look like this.



This worked really well to set those nutserts. A few lessons from the experience I had: It works better with 2 people so one can be focused with the large wrench and keeping everything straight. Otherwise, the nutsert ends up at a weird angle which causes everything to be difficult from there. Don't go crazy with the tightening. You just need to set it not crush it beyond recognition. I found that if you tighten it too much then the threads get a bit bungled which again makes things more difficult.

Good luck.
Use anti seize on the bolt. It wont gull up the treads.
11-27-2012 03:16 PM
richsipe
Creating your own NutSert Installation tool for about $2 in any size

Creating your own NutSert Installation tool for about $2 in any size

Recently I was installing some Crusher Corners from Poison Spyder Customs and one of the rear installation bolts needed either a nutsert or a large hole cut into the tub. I chose the nutsert method as I didn't want a huge hole in the tub but realized that in the large size of the installation bolt I had no way of setting the nutsert.

Luckily I also had the installation kit for the TrailGate which included a provided nutsert kit for both of the sizes of nutserts that were included in that kit but unluckily it wasn't the right size.



After a quick look it seemed like a pretty simple construction:



After a trip to our local True Value hardware store I had the parts to build my own which ended up working pretty well.

The parts to build your own are:
1) Grade 8 half treaded bolt that fits in the nutsert. For mine it was a course thread which surprised me.
2) 2 Washers that fit the bolt. Try to get these as close fitting as you can. Mine was a bit loose and although it worked, it marred the surface of the nutsert a bit.
3) A Coupler that is larger than the bolt that allows the bot to fit through. This will be your holding spot with a large wrench to push down the nutsert onto.



Once you put it together it should look like this.



This worked really well to set those nutserts. A few lessons from the experience I had: It works better with 2 people so one can be focused with the large wrench and keeping everything straight. Otherwise, the nutsert ends up at a weird angle which causes everything to be difficult from there. Don't go crazy with the tightening. You just need to set it not crush it beyond recognition. I found that if you tighten it too much then the threads get a bit bungled which again makes things more difficult.

Good luck.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:53 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC