|08-19-2013 05:06 PM|
|08-19-2013 04:31 PM|
I'll admit I may have attempted to move the lever faster/harder in these instances than typical, but was still surprised by it. There is a brief but fairly powerful jolt when the crunch happens, too.
Have others experienced this? Is this good reason to see dealer?
|02-27-2013 04:03 AM|
My 2nd gear is also "crunchy." Usually it is less of an issue when you shift 2500-3000 rpm. Just today at about 7000 miles I had it pop (not slip) out of 2nd. (2012 JKR)
I'm not a mechanic but I take it that the whole crunchy thing is because of the synchros. I have another issue that may be related. I have had a handful of times where the shifter will be locked in the gate, but not all the way in gear. It happens in 2nd and 4th. When trying to accelerate of course the RPMs jump up and there is a light grinding noise. Taking it back into N and setting it again in gear made it like it never happened. I tried to tell myself that I just put it weak after it happened the first time, but now I think there is more too it than that.
There have also been a couple times where I have not been able to get into 2nd when coming to a place where I'm going to do a slow rolling turn. Basically going less than 15mph, clutch to the floor, I start putting it into 2nd and it will go past the gate but then grind and not set in gear. Both of those times I just came to a stop and put it in.
It's pretty annoying because it only happens maybe once every 2000 miles so there is no way they are going to be able to reproduce it at the service department. I'm hoping a TSB will come out that will address the issue. As far as I know the only one for the transmission is about a faulty boot http://www.wranglerforum.com/f33/tsb...tml?highlight=
|02-26-2013 10:04 PM|
|02-26-2013 09:59 PM|
|miket52989||I got my 2013 jeep in August, and one week later it was in the shop because of this issue. The dealership didn't even take it for a drive and told me that it was normal. My dad 2011 wrangler and my brother 2012 Rubicon told me that it would get better. I am glad now to find this article and prove I am not crazy! . The dealership told me that I will be fine because it is under warranty if I have any issues. I am still having the issue and it has made me want to get rid my jeep. I do not feel safe when pulling into traffic because it does not want to go into second gear. I feel like printing out this thread and taking it to the dealer.|
|02-26-2013 08:44 PM|
|Casotakar1229||hmmm....never thought about this being in issue in my jeep until I read through this thread...thanks a lot. I'm not a hypochondriac...|
|02-26-2013 07:13 PM|
I feel blessed that at least one mechanic at my dealership knows transmissions and cares about the customer.
I was wondering what was the latest with your trans.
|02-26-2013 07:09 PM|
I'm bringing mine in for the rattles and I'll mention this as well. Although, I'm thinking they'll go for a new trans this time.
|02-26-2013 07:04 PM|
I am a very happy Jeeper!
The shift tower was replaced and when I went to pick up my Jeep, the shop foreman showed me the problem. On the bottom of the shift tower is the shift fork. When the shift lever is moved the fork moves between shift rails to change gears. The shift fork was too wide and was hitting on the rails. This caused hard shifts from 1st to 2nd and the "crunchy" feeling. The shift fork on the new shift tower was skinnier.
He told me he replaced a shift tower on another JK for the same issue. he also talked to the Chrysler zone rep for the Denver area and the zone rep said he was already aware of the issue from other dealers. One dealer didn't have a shift tower on hand so the tech machined a couple of thousands of each side of the fork to solve the issue.
Shifts are now smooth yet with positive engagement and no crunchy feeling.
The shop foreman let me snap a cell phone pic of the bottom of the old tower showing the fork and the marks where it was hitting the shift rails. My apologies for the fuzziness.
|02-26-2013 02:00 PM|
Finally had time to drop my Jeep off at the dealer. They had ordered a new shift tower.
Will update later.
|01-31-2013 10:07 PM|
|Con Artist||Mine doesn't grind, but it does feel "scratchy" while shifting from time to time...mostly when it's cold. Pausing in Neutral before completing the shift usually alleviates the issue for me. Plain and simple, this manual just doesn't like to be rushed. If I just take my time, I don't have any issues. Don't expect to row through gears like it's a six-speed in a Corvette.|
|01-31-2013 06:58 PM|
Wonder if it is really the clutch, since you mentioned it happens when cold.
If parked outside and closer to freezing or below, the rubber shifter boot get stiff. Besides popping out of gears ( example you put it away in 1st, second will pop) it is just hard to shift. There are many treads about this. This is what we have done: if parked outside we put it in 2nd gear and turn the heater vents to shifter boot when starting. See if this easy stuff works for you (dealer wanted us to buy the boot and they would install it, but wanted to avoid more trouble with them. They had the jeep previously in 10 F for 5 days and only looked under it, nothing wrong.Later I told them I found this boot issue on this forum and needless to say: THANK you all.
|01-22-2013 01:34 AM|
|01-22-2013 12:35 AM|
|Blastek||i stick it in 2nd with the transfer case in neutral|
|01-22-2013 12:31 AM|
|Deceptionz99||When I start my jeep and let it warm up for a minute when it's realllly cold like 8 degrees. I will just roll through the gears with the clutch in. When I start driving It usually shifts better then if I didn't so it. I do still double clutch second sometimes because that one likes to crunch|
|01-21-2013 11:43 PM|
|SilverSport||The shifter is "gated" to make it harder to accidentally shift into reverse. While in neutral and clutch depressed push the shift lever to the right and then back into reverse with some force.|
|01-21-2013 11:39 PM|
|01-21-2013 11:31 PM|
|01-21-2013 11:27 PM|
I will say it took me a while to get used to the way my JK shifts. A lot longer than my '89 F-250. Im not sure what makes it so different because the Ford was also very low-geared.
I dont mean to change the subject, but what about reverse? I find it a little hard sometimes and the first time I used reverse, it was like I only shifted it halfway in and it made a horrible grind when I let off the clutch. So I quickly pushed the clutch back in and pulled the shifter kinda hard and it finally slipped in there. Anybody else had this problem? ('11 JK)
|01-21-2013 09:20 PM|
|01-21-2013 06:24 PM|
I've noticed this when it's colder out as well.
This morning it was -12 here in MN. Can you say crunchy? Even when pulling out of 1st. And it popped out of 4th on nearly every shift too until I had about 10 miles on the trip. Grrrrr.
Did I buy a 1960s vehicle cleverly disguised as a new one? The 5-speed tranny in my '98 SE was light years ahead of this POS.
|01-21-2013 05:55 PM|
|clayps||Took mine up to have them look at it today. They took it out for a lengthy drive then put it up on the hoist to take a look at a few things. Tech said it felt fairly normal and the added crunch noise when cold is normal as well. I'm just happy its now on record that I had it looked at for that reason.|
|01-19-2013 10:55 PM|
|SilverSport||Shop foreman drove my Jeep, a brand new Jeep, and a 2011 and said they all shifted different. Said he didn't experience the crunch but he was concerned enough about how it shifted that he ordered a shift tower. Will wait and see. He is pretty knowledgeable about transmissions and doesn't believe the issue is in the geartrain, but I am not convinced, yet. When I get the gear crunch on cold mornings, I can feel the sensation in the shift lever. Almost like two objects spinning at different speeds when they try to mesh.|
|01-19-2013 01:13 PM|
|01-17-2013 04:26 PM|
|clayps||Update: I called my local dealership. They want to take it for a drive. Will be taking it in Monday morning.|
|01-17-2013 10:18 AM|
|01-16-2013 09:45 PM|
I picked up my first wrangler the other day. Learned the basics of stick shift from a friend and have been driving around a parking lot after work every day since because I'm waiting on the title to transfer from the previous owner's bank. I drove a motorcycle all through college and thought the shift was the same concept. On cycles, you just hold the clutch and jam the lever into the next gear (downshifting requires something different). So when I started shifting from 1st to 2nd on the JK, I noticed it was notchy and not smooth. I searched around and what you are supposed to do is shift out of first and put a tiny bit of pressure into second while your foot is off the gas and it should slide right in!
|01-16-2013 09:27 PM|
|01-16-2013 09:21 PM|
|01-16-2013 09:10 PM|
What seems odd to me is the six speed in my '11 never acted up in cold weather.
On a side note, called the shop foreman at the dealer and told him what was going on.
Also said my '11 didn't so this. So dropped it off on the way home so he can drive it tomorrow morning. Supposed to drop into the low 20s or teens tonight. He also lined up a new Jeep to drive and compare. He confirmed the synchros can be slow to mesh when the weather is cold, but the "crunchiness" I mentioned got his curiosity.
|This thread has more than 30 replies. Click here to review the whole thread.|