Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > painting factory rims

Join Wrangler Forum Today


Thread: painting factory rims Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-04-2013 07:15 PM
Surfinglbi23 Index cards work great btw tire and rim. Just buy a few packs.
03-04-2013 06:13 PM
Jeeptrd I used a piece of cardboard that slid between the tire and wheel just had to cut it to the same ark as the wheel
03-04-2013 05:59 PM
miketx What did you use to mask off the edge of the rims?
01-21-2013 12:09 PM
Nas.a7x I painteda set of Cherokee rims. I didn't sand them just cleaned primed and painted them. All with rattle cans and am very happy with how they turned out.

Attachment 200316



Attachment 200319
01-20-2013 09:40 PM
sakicnut Search.
01-20-2013 08:31 AM
BAP use a magnet to check them if there steel the magnet will hang to it, if they are aluminum it wont,,,,,---etching primer all the way it,s great
01-19-2013 08:42 PM
firemandad07 Guess i can use etching primer for allow or steel too.
01-19-2013 08:41 PM
firemandad07 I dont really know if they are aluminum or an allow?
01-19-2013 08:20 PM
ajorosa If they are aluminum I highly recommend etching primer first and then what ever paint you want to use. three years for my M/T rims and they still look great.
01-19-2013 08:17 PM
firemandad07 Ok thanks. Just didnt know if i needed to sand all the grooves down or just clean it. I guess if i want a smooth finish i sand them down. But thanks for your reply
01-19-2013 07:58 PM
Fishnic i didnt clean mine, just sanded them down with 100 grit paper in the spots i could reach. i didnt spend alot of time. it has been 10 months and they still look great.

now i would recommend taking more time than i did, sand as much as you can, but dont fear to much if you cant get everywhere. Prep is the key to any paint job!
01-18-2013 09:18 PM
firemandad07
painting factory rims

Good evening all. I am going to paint my factory jeep rims. They have the fine groves on them. All the stuff i have looked at says to sand with 320, 600 and 1000 grit so that they are smooth. Do these rims need to be sanded smooth or just cleaned well during the prep? Any advise from someone who has done this or that knows something about painting. Thanks all.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:23 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC