Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Axle upgrade and swap options

Join Wrangler Forum Today


Thread: Axle upgrade and swap options Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-15-2011 06:44 AM
Lil Thib Well I'm running 36" tires and an LT1 under the hood and it's my daily driver.
06-14-2011 09:18 AM
TheTJRod
Quote:
Originally Posted by Lil Thib View Post
can anyone tell me what vehicle info i need to have to locate an 8.8 out of an explorer?? I recently tore up my dana 35 4:11 gears and want to install a rearend i can depend on...
Any solid rear axle explorer axle will do. 91 and up Explorer, but if you get 95+ you get disc brakes. Also the Mercury Mountaineer is the exact same as the Explorer, 97+.

There is a bunch of info for the Ford 8.8 around.

For the price of a super 35 kit and gears and install you can get a TJ D44 or a ford 8.8 ready to bolt on with locker and gears.

-D35 won't handle 33's for long locked
-Super D35 can handle 33's and could handle 35's with stock engine and smooth driving.
-D44 & Ford 8.8 can handle 35 locked all day.

And now for some tech for the lazy guys.

The axle shaft strength tested by Warn Ind:
F8.8= 6,500 (lb. ft.)
D44= 4,600-5,000 (lb. ft.)
D35C= 4,000-4,300 (lb. ft.)
-------------------------------
COT: Continuous output torque rating
MOT: Maximum output torque rating

(Numbers from January edition of Fourwheeler, page 60.)
Dana 35 rear axle COT: 870 MOT: 3480
Dana 44 rear axle COT: 1100 MOT: 4460
Ford 8.8 28spline COT: 1250 MOT: 4600
Ford 8.8 31spline COT: 1360 MOT: 5100
Dana60 semifloat COT: 1500 MOT: 5500]
06-14-2011 09:11 AM
IndyJeepMan In the front you can run Superior axles 27 spline shafts and install a locker of your choice and be good up to 35's-37's. You can truss if wanted, so if you do wanna swap to a HP30 i would, every inch of clearance is worth it.

A Ford 8.8 with stock shafts and locker will do plenty for what you want. Honestly, if you do no rock crawling and just woods and the like, a 35 with superior axle shafts and a locker would do you fine for the most part.

You can also look into waggy 44's.

06-14-2011 08:59 AM
kjeeper10 I will be following this thread
06-14-2011 07:46 AM
Lil Thib can anyone tell me what vehicle info i need to have to locate an 8.8 out of an explorer?? I recently tore up my dana 35 4:11 gears and want to install a rearend i can depend on...
03-01-2009 08:33 AM
4Jeepn Front HP 30 yes. Might need some adjustment to front Drive shaft.

Rear: Know lots of folks run super 35 kit and have no issues. The 8.8 will take some fab as you stated but is much stronger all around. both are fine for 33-35 tires.
03-01-2009 04:48 AM
jbone03
Axle upgrade and swap options

I've been torn between a few axle upgrade and swap options. So I'm seeking the help of my fellow Jeepers. I currently have Dana 30 and Dana 35 with 3.73's. I'm running a 4" lift with 33" trxus M/T. I have 4.0L with a few bolt engine mods: Banks Cold air Intake, Banks Monster exhaust, TB spacer, and Hypertec programmer. I also have a 63mm TB on the way. I'm running a 5 speed manual transmission. I have been doing allot of research and have come up with these options....

Front:
- Retain Dana 30 and Install 4.56 gears, locker, Alloy USA 30 spline axle shafts
or
- found a HP Dana 30 for $40 which I would do the same mods as above. (I read that this axle has a stronger gear set and would raise the drive shaft for a little more ground clearance)

Both would require a master install kit and any additional seals and gaskets.

Rear
- Retain Dana 35 and Install a Super 35 kit, locker, 4.56 gears. Again I would need a master install kit. ( not wild about c'clip axles and have read that the axle housing is prone to bending so I would also want a axle truss)
or
- Found a Ford 8.8 31 spline axle out of a Ford Explorer for $40. I would retain the stock axle shafts And install a LS diff or locker, 4.56 gears.
I would need a axle bracket kit as well as a master install kit. (Again not wild about c-clip axle shafts however from what I have read the 8.8 axle shafts are stronger than the Dana 35 shafts there fore I have a little more confidence in the ford shafts. Oh and there is always the C-clip eliminator kit.

Because I am currently in Germany hunting down Dana 44's is impossible and ordering axle assemblies from the State will probably cost more in shipping than the axle it self.

I do light to moderate wheeling no rock crawling. This is my daily driver. I just want axles that I can be confident not to break.

Please tell me what you think is most practical, cost efficient. I am working with a budget of about $800-$1000 per axle max. If you know of any other possible swaps please let me know.

Thanks in advance for your opinions, input and help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:26 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC