Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > Do I really need to weld my 8.8 tubes?

Join Wrangler Forum Today


Thread: Do I really need to weld my 8.8 tubes? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-08-2013 04:05 PM
Imped 4 tacks then alternative slow stitches with cooling in between.
02-08-2013 10:13 AM
bajonesy77 The center section is made of steel just like the tubes, you dont need to do anything or use any special welding equipment. Mig or stick for mild steel will work fine.
02-07-2013 02:37 PM
YJ fanatic Alright, I've talked to a few buddies and have access to everything except tig, so what would be best to use, and what rod/wire? And do I need to preheat the cast diff, or just go at it cold? Sorry for all the questions, I'm not a welder.
02-07-2013 12:14 PM
deucestudios mine are fluxed. just like bajonesy said in his last post.
02-06-2013 03:47 PM
bajonesy77 Im not a pro welder or anything but most people over think this. Think of it this way, the tubes are pressed in the center section which gives them the horizontal strength. You are not going to increase that strength by welding the tube to the center section. We are simply putting a bead that connects the center section to the tube to keep them from turning where they are pressed in. Weld a 1/2" tack on one tube then go to the outherside and weld the same tack, rotate 180 degrees and do the same thing. Continue till the whole thing has a weld completely around the tubes. I then made a single pass to dress it all up.
02-06-2013 07:25 AM
YJ fanatic See, I've been researching this everywhere and the majority say use a stick welder and 7018 rod. The thing is, I can't weld well enough to not warp the tubes. And I know some guys that probably can, but I really don't want them to warp, because then I'm screwed. I do want them welded though.
02-06-2013 04:58 AM
bajonesy77 Its not that hard and cheap insurance so why not. I used a 110v flux core welder to do mine. No special rods or anything needed.
02-05-2013 10:21 PM
YJ fanatic
Do I really need to weld my 8.8 tubes?

So I'm in the middle of my axle swap now, and I'm to the point where I need to decide whether to weld the tubes or not. I'm not going to be doing much rock climbing at all, since I'm in Michigan. The only place to do any is at a private off road park, and its not too hardcore at all. I just do the usual trail and dune riding. Are the factory plug welds enough, or do I need to weld the tubes, too? I'll be running the 4.0l and 35s, so it shouldn't stress the axle too much.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:53 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC