Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Key stuck in the ignition

Join Wrangler Forum Today


Thread: Key stuck in the ignition Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-18-2013 09:57 PM
Den06rubi Sure enough! Slot #4 is missing a 10 amp fuse. I'll get it tomorrow when I pick up a blower motor resistor since my blower only works on high. Can't tell you how much I appreciate your help and others on the forum. The information here is invaluable.
02-18-2013 09:43 PM
Black Magic Brakes
Quote:
Originally Posted by Den06rubi View Post
Yep. All good. Thanks. I kept wondering why it was so hard to see when I was shifting into drive or reverse. Never occurred to me it was on upside down/backwards......now...why don't the interior lights come on when the doors open?
Check the dome light defeat fuse behind the glovebox. It may be missing or blown. It exists to defeat the dome light and key chime when the doors are off.
02-18-2013 09:12 PM
Den06rubi Yep. All good. Thanks. I kept wondering why it was so hard to see when I was shifting into drive or reverse. Never occurred to me it was on upside down/backwards......now...why don't the interior lights come on when the doors open?
02-18-2013 08:52 PM
Black Magic Brakes
Quote:
Originally Posted by Den06rubi View Post
Ah, the light bulb and PRNDL cover goes on the left. I was putting it in how I took it out and now that explains why it's now also easier to see
Does the key come out now?
02-18-2013 07:14 PM
Den06rubi
Quote:
Originally Posted by Black Magic Brakes View Post
Pull back and take a pic of the whole front half of the console. Something doesn't look right and I can also tell you that the white section you are holding in place with your thumb is supposed to be permanently attached to the shift bezel.

None of them I have ever worked on had the bulb holder on the passenger side or right hand side of the vehicle.
Ah, the light bulb and PRNDL cover goes on the left. I was putting it in how I took it out and now that explains why it's now also easier to see
02-18-2013 07:03 PM
Den06rubi Just over 2 inches from the lip of the opening to the release mechanism
02-18-2013 07:01 PM
Black Magic Brakes
Quote:
Originally Posted by Den06rubi View Post
Pull back and take a pic of the whole front half of the console. Something doesn't look right and I can also tell you that the white section you are holding in place with your thumb is supposed to be permanently attached to the shift bezel.

None of them I have ever worked on had the bulb holder on the passenger side or right hand side of the vehicle.
02-18-2013 06:33 PM
Den06rubi Attachment 211478

Attachment 211479
02-18-2013 04:33 PM
Black Magic Brakes
Quote:
Originally Posted by Den06rubi View Post
Shifts fine. All I did was pull the plastic up and replace the bulb. Looks like the previous owner had the same problem because he removed the bulb and receptacle from the white piece and had it laying inside. Works just fine without the bulb in.
I've literally had at least 50 of those apart and you have something going on that is not stock. There is plenty of room for the bulb, bulb holder and the wiring harness in the stock set up.

You have to make sure you get the indicator tab in the metal slot and slide the whole mess in with the shifter in neutral so the accordion tabs will fit under the edge, but that's about it.

Can you toss up a couple of good pictures of that area and the bezel?
02-18-2013 03:50 PM
Den06rubi Shifts fine. All I did was pull the plastic up and replace the bulb. Looks like the previous owner had the same problem because he removed the bulb and receptacle from the white piece and had it laying inside. Works just fine without the bulb in.
02-18-2013 03:46 PM
Den06rubi
Quote:
Originally Posted by bardb
It worked before you took it apart. Maybe you didn't get it back together correctly?
It worked fine until I replaced the bulb. Looks like there's not enough room for the bulb so the previous owner decided to remove it.
02-18-2013 11:12 AM
Black Magic Brakes
Quote:
Originally Posted by Den06rubi View Post
Any one else have to lift up the shift indicator (the plastic cover on the shift indicator) to release the key? I just bought an automatic 06 Rubicon and the lightbulb in there was out. When I replaced it the key wouldn't come out. Seems there's not enough room in there. New to the Jeep and not familiar with the terminology but there's a spring mechanism in there that allows the key to release. What's the best solution?
Try it again and push the shifter all the way forward to see if it will click in to release the key. If not, you either put the shifter bezel back on incorrectly or the cable for the interlock is out of adjustement.

There is a cable from the shifter up to the ignition that stops the shifter from being pulled from park unless the key is on and stops the key from being removed unless it is in park.
02-18-2013 10:00 AM
TJDave Does it shift ok? Can you get it in park or 1st gear? If not, it could be the plastic rod inside shifter has broken. Easy fix. Pull up hard on shift knob to remove it. If you can pull out the white plastic rod out of the shifter, it is broken and that is your problem. Simply cut a piece of plastic coat hanger, or chopstick to the same length as the broken piece, replace and away you go.

Not sure if that is your problem, but this is very common on the 42rle tranny.
Just a suggestion and something to watch for in the future if yours has not broke yet.
02-18-2013 09:45 AM
bardb It worked before you took it apart. Maybe you didn't get it back together correctly?
02-17-2013 10:38 PM
Den06rubi
Key stuck in the ignition

Any one else have to lift up the shift indicator (the plastic cover on the shift indicator) to release the key? I just bought an automatic 06 Rubicon and the lightbulb in there was out. When I replaced it the key wouldn't come out. Seems there's not enough room in there. New to the Jeep and not familiar with the terminology but there's a spring mechanism in there that allows the key to release. What's the best solution?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:45 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC