|05-06-2013 08:39 PM|
|piercejoelm||Check your vacuum lines. Mine would not engage either on a 95 4.0. I checked all the wiring and traced the vacuum lines by the teams to the transfer case going into the switch, all were fairly new and in tact. I opened the hood and the vacuum hose that went to the most aft nipple on the intake popped off. I put it back on and threw a clamp on it. It immediately worked with the lights and all. Spending time looking for a bad vacuum line is a lot cheaper than doing a $150 mod that you probably do not need to do yet. Just my .02|
|05-06-2013 01:44 PM|
|05-06-2013 11:11 AM|
Here is what they look like.
|05-06-2013 10:58 AM|
The jeep cherokes have the same kind of 4wd switch on the Transfer case but instead of it having vacum ends on it, it instead has an electric end and you can buy the matching pigtale that plugs into it. It will be a two wire pigtale and all you have to do is run the single wire from the firewall thats off the 4wd vacum light indicator switch and wire it directly to the new Transfer case switch and ground out the second wire thats on the Transfer case switch.
When you shift the T-case the new switch will finish the circuit and ground out the wires just like the 4wd vacum light indicator switch did just without using and vacum.
So what my front axle is always locked. At least i know my 4wd works all the time and i don't feel any problems with the axle being locked.
|05-05-2013 10:47 PM|
|05-01-2013 10:40 AM|
agreed but i did the washer trick in the half shaft lock. even cheaper. almost free. i had washers laying around but i bought a 4wd indicator switch from autozone for cheap that's for a chearoke and installed it into the t-case and ran the wire and that works great!
|05-01-2013 08:46 AM|
|dancin1||Get a diff lock, cable manually operated. $150.00 and never have that problem again, or fix the vacuum system for $150.00 and probably do it again, and maybe again. My diff-lock works great, would never go back.|
|05-01-2013 01:11 AM|
|1994 jeep girl||Its the vacuum hoses. I found out they had melted in half some how.|
|04-30-2013 11:25 PM|
|Aswellguy||Any luck with your jeep? I have the same problem... Changed actuator and transfer case switch... Still no luck.|
|04-01-2013 12:42 PM|
|03-31-2013 09:55 PM|
|cakes567||I would check the actuator first. Its very very common to get stuck. If that's not struck then check your lines and go from there.|
|03-31-2013 08:52 PM|
|Gunz n tractorz||Check the vacuum lines. Put in 4wd and take lines off off diaphragm and see if there is suction on the lines. In not there is a problem with the lines, such as they have a hole in one of them or they just ripped in half like mine did.|
|03-31-2013 12:05 PM|
|JD95YJ||the vacuum is notorious for going out on YJs.. Sometimes the diaphragm just gets stuck and you can remove it and get it unstuck by moving it a few times, using compressed air, etc.. You can replace the diaphragm, or add on a Posi-Lok system, or other ways to get around it as well. Good luck!|
|03-31-2013 12:02 PM|
|1994 jeep girl||The light doesnt come. It has a few wiring problems so i thought it was just a part of that.|
|03-31-2013 04:20 AM|
|Highvan||Does the light come on when you put it into four wheel drive? On my 87, there is a red hose that has to be "T" - ed into a vacuum hose. When i first got my jeep, mine worked fine, then i swapped in a bunch of new parts under the hood and i knocked that little hose off by accident and didn't realize it, then the next time i went to use my four wheel drive, the light wouldn't come on and the four wheel drive wouldn't work, so my guess is, that's what's wrong with yours, cause as soon as i reattached it, it worked fine again|
|03-31-2013 03:45 AM|
|1994 jeep girl||
My 4wd wont engage.
I have a 94 yj 4cyl 5 speed. I can put it in 4lo nd it gears way down like it should but my front tires wont pull. The drive shaft spins nd the hubs nd axles r fine. My cousin said i may need to "pen" the vacuum hose. Has ne one else had this problem?