Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Cracked transfer case rebuild help

Join Wrangler Forum Today


Thread: Cracked transfer case rebuild help Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-11-2013 05:56 PM
OverkillYJ What caught me was getting a 92 TC to swap the gear into my 95
04-11-2013 05:36 PM
2xs There is an early cut and later cut on those planetary gears, I ran into this swaping the input gear from a 02 liberty into a 93 cherokee tcase.

Thsi is mentioned on the Novak weboste:

The Jeep New Process / NVG 231 Transfer Case

http://www.novak-adapt.com/knowledge...nput_gears.htm


http://www.novak-adapt.com/knowledge/ax15.htm

http://www.novak-adapt.com/knowledge/nv3550.htm
04-11-2013 11:22 AM
OverkillYJ First off you should be running ATF, not oil. As far as the input, you need to research exactly what two cases you put together. The planetary gears are not all cut the same. If you turn them by hand and have the wrong planetary gear/input combination it will look perfectly fine. It is not until they are under power you will hear problems.

I learned this the hard way swapping an input to my TC from another TC. Everything looked perfect. Put it back together and right away I knew something was wrong. I looked into it and most people dont know about this problem, but it does exist.
04-11-2013 08:36 AM
saylorv
Cracked transfer case rebuild help

So, here's the story...
I cracked my tcase in half doing less than an honorable stunt... I went to the bone yard, pulled one out of a ZJ. Tore it apart, swaped the inputs, using the one out of the cracked YJ into the ZJ case. Figured it would be an easy swap. Installed the new case, it shifted into/out of 4x4 fine, everything was golden, but over 25 mph, it whines. I had ATF in it at first, I drained that, put 80W90 in it. Still same whine. I now have the Tcase out and taken apart. I checked all the bearings, they all seemed fine. However, when I spun the input shaft around in the tcase, it had the same whine to it like it did when I was driving. I pulled the input out, spun all the planetaries, they all are fine. It just seems like when they're spinning within the ring in the casing, thats when I get that whine. Is it the ring or input? I'm lost. I have got to have this DD back up and going. Please help

Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:04 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC