Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 2.5 nightmare

Join Wrangler Forum Today


Thread: 2.5 nightmare Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-07-2013 10:38 PM
jokerchief462 Take the valve cover off clean the baffles at the PCV or CCV. Replace the hoses to the valve cover with new just to make sure they aren't collapsing when warmed up. Check oil level and ensure it is not over filled. The oil pump has a pressure relief at 75psi so it should be regulating the oil pressure for you. If not I would suspect the pump if nothing else is found. From your beginning numbers you have a lot of life left in the engine. See how all that works. I would hate to just jump on the pump first.
05-07-2013 07:23 PM
jasontibbs Update ..... ECM fixed starting issue now on to the crankcase pressure issue
04-30-2013 04:26 PM
jasontibbs 94 but the engine was rebuilt 12000 miles ago and developed this problem at 10000 miles
04-30-2013 03:00 PM
Garyk Sometimes no, sometimes a crack will open up after the engine gets warm.....I saw once where the ring gaps were all lined up...not too common unless installed wrong.

What year is this engine?
04-30-2013 01:17 PM
jasontibbs But wouldn't either the leak down or compression test shown that
04-30-2013 11:16 AM
Garyk Agree with C.L. on the wiring, something is shorted or connection is bad by the sounds of it. If the engine is blowing oil and blowing the dipstick out, there has to be excessive pressure in the crank case, Did you do the compression test and leak down when the engine was hot? There's only a few causes of blowby, cracked/holed piston, cracked ring, cracked block or blocked/faulty emissions
04-29-2013 10:56 PM
jasontibbs Bump
04-27-2013 11:15 AM
C.L. Sounds like the main harness is partially melted and some of the wire cores are touching. A buddy of mine with the 2.5 had similar issues (would sputter and die when wet, fuel pump would intermittently lose power, sometimes wouldn't start, etc) that were traced back to a connector that had sagged down enough to touch the exhaust. Once ONE positive wire melted to the exhaust it shorted and melted insulation off other wires further up the harness. They were randomly contacting/jumping and wreaking havoc with the electrical system, but never blew fuses for some reason...
04-27-2013 11:06 AM
jasontibbs Bump
04-26-2013 09:53 PM
jasontibbs
2.5 nightmare

ok so this is the long version.... a buddy had me bring his jeep over to do some repairs and holys$%t this thing is tore up. first a little history the motor has 12000 miles on a rebuild that was done at a rebuilder in chicago.then the motor sat for 8 months till it was installed.then the motor was installed and went through a proper break in period. at roughly 10000 miles it started blowing the dipstick out of the tube about 2 inches and would push a little oil out every now and then.now it is in my garage (along with 2 more project builds).. it has also got another issue.when trying to start it there is no CEL but after trying to start it 12 to 15 times the CEL will come on and then it will start. now is where i am having a problem i have done a compression check
#1 has 150 psi
#2 has 145 psi
#3 has 143 psi
#4 has 150 psi
so i did a leak down test and the results are
#1 10%
#2 15%
#3 12%
#4 10%
all are within acceptable specs so now i checked the pcv valve and vaccum line and system all good with minimal oil in the pcv line and the scavange line that goes to the throttle body. so i cleaned them anyway so with these two issues let me add 1 more.
when you try to start it and the CEL come on so do the headlights but just dim not normal brightness for low beam almost like a dead flashlight.

so i hope someone can come up with some ideas cause i am lost at this point. i am thinking small crack missed during rebuild possibly. and during leak down test you cannot hear where the leak is i have tried smoke in all places watching for movement but get none
hopefully some has an idea.......:deadhors e:

thanks guys and gals

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:11 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC