Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Manual Transmission Drain Plug Tool

Join Wrangler Forum Today


Thread: Manual Transmission Drain Plug Tool Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-25-2013 10:23 AM
TOK Not sure if this clearance issue affected all JK's at one time, but I have a 2013 Sport and the pipe that crosses under the trans drain is far enough forward that clearance doesn't appear to be an issue.

I simply went out and purchased two bolts, one with a 17mm head and the other with a 14mm and put two nuts back to back at their centers.

Total cost for all of it was under $5. Going to order Redline MTL, which no local place has on the shelves. I will update if there are any complications with this setup when I'm done.
06-25-2013 09:57 AM
legitposter A bolt with a 17mm head and a 17mm nut attached is the cheapest route but I went around to every hardware store and couldn't find bolt heads that big. I was surprised.

A trimmed 17mm hex tool would work great as well but I don't think I have the tools to cut a hex tool right now.

I ordered a tool piece similar to what another poster responded with. I'll post results if they're good.
06-25-2013 04:41 AM
kjeeper10 Cheapest tool I've seen is a lopped hex tool. Used a open end wrench to remove the plug.
Problem is you do bot have a lot of room. Cut just enough to fit the plug and enough for the wrench to grab onto.
06-24-2013 04:31 PM
fljeepleo
Quote:
Originally Posted by lakemm21 View Post
I too am a newbie to jeeps and have wondered this very same thing. I called a jeep dealer and they told me they use a 1+ inch 17mm hex socket from Matco. It's $16 minus shipping. The part number is BP17MA should the link below not work. Excuse us for cheating!

BP17MA 17MM DRAIN PLUG SOCKET
Nice, gonna have to add that to the collection.
06-24-2013 04:28 PM
lakemm21
Manual Transmission Plug Tool

I too am a newbie to jeeps and have wondered this very same thing. I called a jeep dealer and they told me they use a 1+ inch 17mm hex socket from Matco. It's $16 minus shipping. The part number is BP17MA should the link below not work. Excuse us for cheating!

BP17MA 17MM DRAIN PLUG SOCKET
04-29-2013 02:46 PM
cnhmatthews
Quote:
Originally Posted by Chrimbler View Post
You're too lazy to fabricate the tool, but not lazy enough to change your own oil??....
It's really not that hard to make one, get a 17mm allen key, cut a one inch section off or get a 1" M17 bolt and 2 nuts.
Here's your answer. Just fine a bolt with 17mm head and thread 2 nuts on the end and tighten against each other. Use this method and Si Robertson would be proud of you.
04-29-2013 09:40 AM
Rooster76 It shows how to make one, and the clearance your working with HERE> Project-JK.com - Jeep JK Wrangler Resource » Jeep JK Wrangler NSG-370 Manual Transmission Service

I'm wondering if this 17mm one would work for the tight spot? Maybe not because it's a socket.
BGS Tools 1/2" Bit Socket Int. Hex. 17x55mm 5184-H17 on eBay!

Looks like you need a 14mm one also, but it doesn't need to be so short.

If you find a cheap spot to get one post it up.
04-29-2013 09:30 AM
Chrimbler You're too lazy to fabricate the tool, but not lazy enough to change your own oil??....
It's really not that hard to make one, get a 17mm allen key, cut a one inch section off or get a 1" M17 bolt and 2 nuts.
04-29-2013 09:20 AM
chipmonk66gt It needs a special tool? Can you post a pic? I'm curious. I would imagine it would have been a 3/8 socket like most drain plugs.
04-29-2013 08:18 AM
SackLunch bump.....anyone?
04-28-2013 07:09 PM
SackLunch
Manual Transmission Drain Plug Tool

Would anyone be willing to send / sell me their tool they used to unscrew the manual transmission fluid drain plug? I'm too lazy to fabricate one myself.

Or any tips on a work around the exhaust manifold would be appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:27 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC