Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Trackbar & draglink length

Join Wrangler Forum Today


Thread: Trackbar & draglink length Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-05-2013 04:26 PM
MLaborde
Quote:
Originally Posted by Jerry Bransford View Post
The darting is why I suggested checking/setting the toe-in. I think one of my edits to that post accidentally deleted why I was talking about setting the toe-in. And when is the last time you had your caster angle measured? An out-of-whack caster angle can make the steering less stable.

I set the toe-in after installing the gearbox 2 weeks ago. I double checked the toe-in last week when troubleshooting before ordering the new trackbar. I WILL triple check it Monday since I'm off work part of the day.

I never have had the caster angle checked. I have stock CA's so I thought it was set & couldn't be adjusted.
05-05-2013 03:51 PM
Jerry Bransford The darting is why I suggested checking/setting the toe-in. I think one of my edits to that post accidentally deleted why I was talking about setting the toe-in. And when is the last time you had your caster angle measured? An out-of-whack caster angle can make the steering less stable.
05-05-2013 03:46 PM
MLaborde
Quote:
Originally Posted by Jerry Bransford View Post
The drag link & track bar must be at the same angle, not the same length. And with a stock Pitman arm and stock track bar mount, they will be at the same angle so no worries there.
Thanks, Jerry. I originally learned how to set my toe-in from your info 2 years ago. You have been a huge source of info for me since I joined here then.

I have the same angle on the TB & DL so I guess I'm good there. I never stopped to think that as long as my pitman arm was pointed to the rear, the lengths should be the same.

I guess all of that I read about only applies to adjustable TBs. Knowing that the lengths are OK with the angles being good would be great news except for the fact that I was hoping that the length issue I had read about was the source of my problem.

Dry steering test seems good so unless it is the ball joints at the wheels (as recently suggested on "another" forum where I've been documenting my woes as they have changed - that thread title is now very misleading), I'm stuck.

Thanks again for your help today & in the past!
05-05-2013 03:02 PM
Jerry Bransford The drag link & track bar must be at the same angle, not the same length. And with a stock Pitman arm and stock track bar mount, they will be at the same angle so no worries there.

The tie rod length is set first by adjusting the tie rod length so the front edges of the tires are 1/16" to 1/8" closer together in front than they are in the rear. Then the drag link length is adjusted to center the steering wheel.

Here's a good basic guide to the TJ's alignment procedure... Basic Jeep Front End Alignment

And while a tape measure can be used to measure between the tires when setting the toe-in, the below indicates a more precise/more repeatable way of measuring. It only requires two pieces of 1" square aluminum tubes & two spring clamps. Mark the tubes at the two points to equal your tire diameter & measure between them at the marks.
05-05-2013 02:48 PM
MLaborde
Trackbar & draglink length

Long story short, When I replaced my steering gearbox I replaced the tie rod end on my DL and just eyeballed the depth when I screwed it in (I had cranial-rectal syndrome). I also replaced my front trackbar with a stock (non-adjustable) trackbar. Toe-in set & steering wheel straightened.

I'm having a LOT of darting left & right when driving but steering is pretty tight. It doesn't necessarily happen when I hit bumps & does it randomly even on a smooth, straight road, There is no dead spot in the steering wheel and I can mostly run straight with the steering wheel at 12:00 but sometimes the steering wheel has to be held at either 11:00 or 1:00 to run straight, also. However, I don't have to steer back & forth to hold a straight line like I did when my gearbox was shot.

Hours of reading these forums makes me think that at least one of my problems is that I got the DL length wrong when I put on the new tie rod end. As I understand it, the DL & TB must be the same length.

What is the tolerance on this relationship? For example, can I be off by 1/8" or 2"?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 11:10 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC