Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 92 YJ Automatic 4 Wheel drive H, L wont engage

Join Wrangler Forum Today


Thread: 92 YJ Automatic 4 Wheel drive H, L wont engage Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-14-2009 07:14 PM
fourdoorfanatic actually, all my lines are broken, so i leave a plugged engine vacuum line tied to the side by the front axle and engage/disengage my front axles manually. poor idle could be a vacuum leak somewhere. i have plenty of those.
05-10-2009 02:26 PM
bbanks11 Ok I disconnected the vacuum hoses from the transfer case and one out of the four hoses have a vacuum. I traced the lines back and the one with a vacuum lead to or around the manifold. Two of the lines lead to the shift motor located on the front axle and the third line at the moment leads no where ( the line just ends and is not connected to anything). I did notice that the line that did have a vacuum split off and connected to fuel line vacuum. I noticed that where it connected to the fuel line the rubber was worn so I temporarily fixed it with tape, and now engine is not running properly. She will idle for a while and just cut off.

Any helo would be great
Thanks
Bryan
05-01-2009 06:59 PM
yburn I'd check your vacuum on the axle before the t-case,They go out all the time!
05-01-2009 09:58 AM
bbanks11 Linkage checked and all looks well. It goes into the appropriate gears but does not engage the front drive shaft. I can get 2x4, 4x4 nuetral and 4x4 low but all in 2wd. I'm thinking it may be the transfer case itself. Any help would be greatly appreciated.
Thnx B
04-28-2009 09:01 PM
buckshot500 I'd pull up the boot, & take a good look & try it while looking for anything blocking the linkage. You may have to crawl under there to get a better look. Don't do this until everything cools down, or you'll find out quickly what stuff gets hot while you drive.
04-28-2009 07:34 PM
yburn Does it have a lift?? Check you linkage my be in a bind?
04-28-2009 07:22 PM
bbanks11
92 YJ Automatic 4 Wheel drive H, L wont engage

I have a 92 Sahara Automatic Trans, and both 4H and 4L will not engage. I am able to get it into 2H and Neutral but nothing else. Any possible "easy" fixes before I shell out a lot of money?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:23 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC