|05-06-2013 10:30 AM|
|05-04-2013 04:53 PM|
|05-04-2013 01:11 PM|
|05-04-2013 11:31 AM|
Well, i finally got to it with a friend since I couldnt hold the bolts and start the screws at the same time!
The BEST way i found to get the Torx bolts out, was to use a heat gun on them for a short period of time and NOT use the Napa Torx heads. As soon as I switched to the Snapon ones they quite breaking!
It took about 3 hours to get the first windshield hinge and door hinge set done, cuz the 4 bolts that are hardest to get at had to be drilled out as they just spun. Then we had to figure out how to get a nut up there to bolt into.
The 2nd side took like 30 minutes...lol... cuz we had it figured out!
So this week i will take it in and have the new windshield installed. Then I will have to choose which way to fix the carb issue... nutter, new or efi...
|03-04-2013 02:02 PM|
|superdiver||great info, thanks! I will give it a try....|
|03-03-2013 03:50 PM|
Yep. You need to clean off the body sealer coating the nuts.
The lower hinge nuts can be reached without removing the dash, but might be a real challenge if you have big hands. Even so, you are working blind by feel, and it's a real PITA when you drop a nut back there and it disappears into the void behind the dash. I dropped one and it didn't reappear until a few months later :laugh:. Getting a wrench back there is a PITA too. Moreso for the driver's side than the passenger side.
When you get the nuts and bolts reinstalled, be sure to re-seal the nuts with RTV or the like to prevent water from leaking in.
One thing I learned was that some torx bits are made with metal that is just too damn soft to be useful.
|03-03-2013 02:48 PM|
The nuts are not welded to the body. They used a body sealer, and coated them with it. You can get at them without pulling the dash out, but it is really tight. You'll need something to pick the sealer off with, then you can put a 1/2" wrench on the nut. Just went through that on mine. Swapped out my windsheild and hinges.
PS: When I loosened the Torx screws off, I used my torches with a brazing tip to heat the bolts first. One swat with a hammer and center punch, and the Torx came loose right away.
|03-03-2013 11:42 AM|
All we have is napa... and ace hardware...
Anyway, i picked up a napa one and some pb. Yesterday I used them and it worked KINDA.... I got all the bolts loose on the one side, but on three of the bolts the NUTS came unweldied on the INSIDE! so those three bolts just spin....
Now I am trying to figure out how to access that area! It looks like I have to remove the dash COMPLETELY.... any ideas or hints?
|02-28-2013 03:31 PM|
|02-28-2013 03:02 PM|
|Garyk||A hammer impact drive is one you hit with a hammer, gives a good impact and turn the torx a small amount. The idea is the impact breaks the rust.....a word of advice, be careful if you are using one on the upper windshield/roll bar bolts....you can crack the windshield....don't ask how I know Fortunatley I had to replace the windshield anyways.|
|02-28-2013 02:16 PM|
I believe my impact was a hammer impact.. maybe not... whats the difference between a "regular" nuematic impact driver and a hammer impact driver?
I might pick up a manual impact driver at napa for the weekend...
|02-28-2013 01:52 PM|
|02-28-2013 12:48 PM|
Air impacts ARE NOT as good as manual impacts for this..... ask ANY old motorcycle guy..... we used it for PHILIPS head bolts for years....... works just as well with TORX..... I pull stuff apart all the time on my Jeeps with my Impact Driver...... bought it at Sears over 25 years ago.......
and... if you can get it.... KROIL is way better than PB Blaster..... proven in lab testing....
and..... you MAY have to break the paint seal to get ANY of these products into threads....
Craftsman Impact Driver - Tools - Mechanics & Auto Tools - Automotive Specialty Tools
|02-28-2013 12:44 PM|
|OverkillYJ||You need a hammer impact driver. It is a must for stuck torx unless you want to end up using EZ outs.|
|02-28-2013 12:37 PM|
I have been using an air impact wrench, the torx inserts keep breaking
Also, most the nuts are still covered with paint.. how do I get the pb to the threads?
|02-28-2013 11:39 AM|
|Garyk||If you have a "good" torx bit, try an impact driver ( the kind you hit with a hammer) works for me..|
|02-28-2013 10:28 AM|
Just hit the with this. That thing breaks all kinds of stuff free for me. That and a little PB.
|02-28-2013 08:51 AM|
|90DesertTanYJ||When I did my door hinge torx, I sprayed them with PB every day for a week and used an 18V impact each day for a little bit until they gave up. Just be careful to hold the impact straight and keep pressure on it so it doesnt strip out the head. After they strip, welding a nut on is about the best option. Not only do you get something to grab on, the heat from the welding will help loosen the bolt.|
|02-27-2013 08:03 PM|
Or just get these http://buy1.snapon.com/catalog/item....store&tool=all and pick up the exrractors elsewhere.
Left hand bits are the 'trade secret' to broken bolt removal. They cut in "reverse", which also tends to unscrew the bolt before the extractor is needed. When drilling, use machinist cutting fluid or distilled water to cool the bit, do not use wd40 for any part of it. Use PB, as said, on the threads. When using an extractor, work it slowly. For every 1/2 turn or so it should be turned back (tightened) about a 1/4 turn.
|02-27-2013 08:02 PM|
PB Penetrating Catalyst
Dang good stuff on rusty bolts!
|02-27-2013 07:42 PM|
not heard of that... what is it?
|02-27-2013 06:32 PM|
|173ABN VN||use liberal amts. of pb blaster...russ|
|02-27-2013 06:18 PM|
LOL.. thats exactly what I have been doing.. but it sucks to have to do that.. i was hoping for "the silver bullet" "the magic trick" "the trade secret"
All I had was beer, boredom, and a welder... thats a DANGEROUS combination!
|02-27-2013 01:39 PM|
|tylerf83||weld a nut on and use a socket or wrench worked well for me|
|02-27-2013 01:34 PM|
Torx bolt problems...
I am replacing a bunch of old rusty parts on my 89 YJ. But am having a heck of a time getting out the torx bolts.... i keep breaking the torx sockets...
any tips on how to get these bad boys out effectively??