|05-06-2013 02:22 PM|
|05-06-2013 01:52 PM|
|Relocatedduckman||Where do you live? I've got my rear drive shaft that's in great shape. Replaced it with my sye and Tom woods.. If you pay shipping.. All you need is 2 u joints and your good to go..|
|05-06-2013 01:02 PM|
|05-06-2013 12:03 PM|
|05-06-2013 10:43 AM|
|05-06-2013 10:37 AM|
Alright thank you, as long as the slip yoke is for the NP231 it will fit, correct? I see some on eBay from spicer but it says its for 87-95 yj :/
It says it'll fit up to 00' and I have a 05'. I just don't want to order it and it be to long
|05-06-2013 09:57 AM|
|Jerry Bransford||The only fix is simply buy a replacement output shaft yoke. You should be able to pick one up from RockAuto Parts Catalog|
|05-06-2013 06:38 AM|
So I was putting the ujoint inside the slip yoke using a press then all of a sudden the flanged edge for the snap ring shattered right off. Due to my negligence, do you have any ideas for a simple fix? I want an sye but can't afford a new sye, cv shaft, and upper adj CA. So for now just gonna fix the yoke.
|05-05-2013 12:17 PM|
|Jerry Bransford||It's not even close to being bad enough to need replacing. At least not from what I can see.|
|05-05-2013 12:16 PM|
|bmanrkg3||Sounds like a good excuse for a slip yoke eliminator kit... ;-)|
|05-05-2013 12:11 PM|
|Lotek||Theirs no chip on the spline coming out of the transfer case, so am I kinda stuck buying a whole new slip yoke?|
|05-05-2013 11:59 AM|
|Jerry Bransford||The Wrangler's factory slip joint is not indexed.|
|05-05-2013 11:54 AM|
|s14sh3r||Look at the shaft and see if there's a corresponding flat spot. I'm not sure on Jeeps, but I've seen other vehicles that were made that way as an index.|
|05-05-2013 11:52 AM|
|Jerry Bransford||Don't put too much grease inside the opening, just grease the splines themselves. Too much grease inside there can prevent the driveshaft from sliding in as far as it needs to at times which can cause major damage to the t-case or rear axle.|
|05-05-2013 11:48 AM|
|Lotek||Here's the side view, I just wasn't sure if I should take a wire brush and use some WL grease or just pump it with bearing grease. It also appears the part in the picture below has a tooth chipped? Any thoughts? Sorry for so many questions, I'm still new to all this stuff!|
|05-05-2013 11:42 AM|
|s14sh3r||The splines look good, just dry.|
|05-05-2013 11:37 AM|
|Jerry Bransford||What, surface rust? Unprotected steel will rust, apply some grease to the splines & put it back together if that is all you're asking about.|
|05-05-2013 11:33 AM|
|4Jeepn||What's fishy about it? also what is a side view of the part in your hand?|
|05-05-2013 11:24 AM|
Need help quick (u-joint), is THIS normal?
Was changing the front u joint on the rear driveshaft and when I pulled it out I saw this.
Do you guys see any problems with the pictures I took? I don't know but it just seems "fishy".
05 tj 6spd by the way. Thanks guys!