Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Terraflex 2.5 spring lift folks in here.

Join Wrangler Forum Today


Thread: Terraflex 2.5 spring lift folks in here. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-29-2013 11:14 AM
XTRyan
Quote:
Originally Posted by ohioviper View Post
So I think I want to buy longer SS brake lines and discos. Any recommendations on which ones.I am also considering removing the bumb stops for max flex .Any of you done this ?
You don't want to remove the bumps tops because then you run the risk of over flexing the Jeep and damaging the tire, fender flare, or shocks. there is a ton of info on proper bumpstop setup out there. This Thread has some of the best info I have read.

As for the brake lines, we carry Crown Performance and they are great. They are available in lengths from stock to 6" longer than stock. They'll give you more than enough room for flexing your Jeep out.

I hope this helps!

-Zach
05-29-2013 10:57 AM
whiteyjfm
Quote:
Originally Posted by ohioviper View Post
So are you talking about unbolting the hard line from the frame bracket or unbolting it from the axle ?
No, unbolt it at the bottom at the axle, just at the bottom of the coil spring. You are supposed to unbolt it to lower the axle to install the coil springs. Just leave it unbolted.

I will take a picture and post it.
05-29-2013 08:29 AM
JTPhoto JK If you go with discos you will need either the exhaust spacer or different front driveshaft otherwise the factory driveshaft will hit the exhaust.
05-29-2013 08:25 AM
ohioviper So I think I want to buy longer SS brake lines and discos. Any recommendations on which ones.I am also considering removing the bumb stops for max flex .Any of you done this ?
05-29-2013 07:40 AM
ohioviper Yea I notice my rear line was rubbing shock couple days after the lift. I bent the bracket so now they dont rub.

JJPhoto I get what you are saying about the bracket on the axle now. Im just not sure whether to modify the stock line and bracket or just go ahead and get longer ss lines. And no I didnt do the exhaust spacers as they look like they are not made to last.
05-28-2013 11:53 PM
mistasparkl I unbolted mine from the frame bracket. Bolted it to to a stanley tee, and then to a lower spot on the axle. Cost me 5 bucks. I used some guy's write up on jkf.
2011 Front Brake Line Relocation - Correct TF BB Lift Design
05-28-2013 11:04 PM
JTPhoto JK
Quote:
Originally Posted by ohioviper View Post
So are you talking about unbolting the hard line from the frame bracket or unbolting it from the axle ?
Sorry viper back to your original question.
There is a bracket on the rubber brake line, not the steel line, unbolt that bracket, and tie the rubber brake hose back. A friend of mine carefully cut the bracket off the hose so it wouldn't snag on anything.
05-28-2013 11:00 PM
MichaelEdwardsDO
Quote:
Originally Posted by WhiskeyMike View Post

Ohio, just a quick note. Your rubber flex brake line looks awefully close to the shock. It might just be perspective of the camera, but... When flexing, mine bent a bit and put the half loop against the shock and I didn't notice it for a couple weeks. Normal vibration rubbed a bit of the texture off the rubber. If it had stayed for a couple more weeks, it would have rubbed it pretty thin weakening/breaking that line. Since then , I have pulled it away including bending the bracket a bit so it stays off a few inches. Thought you might want to check it out and see if it needs to be pulled away.

I plan to change them out for a stainless braid set as soon as I gain up the nerve to bleed my brakes. Not hard, but had a painful experience in the past.
I hate bleeding brakes. It's one of the few things that seems so easy that can really ruin an afternoon!
05-28-2013 10:58 PM
WhiskeyMike
Quote:
Originally Posted by ohioviper View Post
Took pic just now in the dark so best I can do for now.
Ohio, just a quick note. Your rubber flex brake line looks awefully close to the shock. It might just be perspective of the camera, but... When flexing, mine bent a bit and put the half loop against the shock and I didn't notice it for a couple weeks. Normal vibration rubbed a bit of the texture off the rubber. If it had stayed for a couple more weeks, it would have rubbed it pretty thin weakening/breaking that line. Since then , I have pulled it away including bending the bracket a bit so it stays off a few inches. Thought you might want to check it out and see if it needs to be pulled away.

I plan to change them out for a stainless braid set as soon as I gain up the nerve to bleed my brakes. Not hard, but had a painful experience in the past.

To your original question, I have the same setup and have had no issues at full flex. I assume your install included the exhaust extension? That's the only issue I know of when at full flex.
05-28-2013 10:57 PM
JTPhoto JK So I was out just checking our Jeeps, both with TF kits and the bumpstops will hit before the swaybar links can contact the brakelines.
From what I could see in the pics on the other thread the 2 guys with issues didn't seem to have extended rear bumpstops.
05-28-2013 10:52 PM
JTPhoto JK
Quote:
Originally Posted by ohioviper View Post
Mine are in fact the extended TF links. The stock rear ones were moved to the front per the kits instructions.
Yup no prob.
05-28-2013 10:47 PM
JTPhoto JK
Quote:
Originally Posted by Barmanvarn View Post

Not sure how you can tell they are factory links. The TF links that come with the kit are just like stock, only longer.
Must just of been the angle of the pic. They just looked short.
05-28-2013 10:30 PM
ohioviper Mine are in fact the extended TF links. The stock rear ones were moved to the front per the kits instructions.
05-28-2013 09:48 PM
Barmanvarn
Quote:
Originally Posted by JTPhoto JK View Post
Looking at vipers pic you can see that he has the factory rear links. The only way I can even imagine the rear swaybar link coming close to that brakeline is if you have a lift with the short factory links and when you flex out full, the staybar comes down near vertical.
Mounted inboard or outboard my links come nowhere near the brake line. If the brakeline drop brackets are used and put on properly you would have even more room.
Not sure how you can tell they are factory links. The TF links that come with the kit are just like stock, only longer.
05-28-2013 09:45 PM
JTPhoto JK Looking at vipers pic you can see that he has the factory rear links. The only way I can even imagine the rear swaybar link coming close to that brakeline is if you have a lift with the short factory links and when you flex out full, the staybar comes down near vertical.
Mounted inboard or outboard my links come nowhere near the brake line. If the brakeline drop brackets are used and put on properly you would have even more room.
05-28-2013 09:41 PM
Barmanvarn
Quote:
Originally Posted by MichaelEdwardsDO View Post

Read than last sentence out loud to some who knows nothing about jeeps please
Btw mine are outboard.
Ya know, as I typed that I realized how it sounded but was too lazy to reword it.
05-28-2013 09:37 PM
MichaelEdwardsDO
Quote:
Originally Posted by Barmanvarn View Post

Yeah. I read inboard for factory wheels and outboard for after market wheels.

I'm gonna have to flex my rear to ensure I can't snag my break lines.
Read than last sentence out loud to some who knows nothing about jeeps please
Btw mine are outboard.
05-28-2013 09:30 PM
Barmanvarn
Quote:
Originally Posted by JTPhoto JK View Post
This is not the proper way. But this is how the rear links are mounted when you have extended swaybar links and factory wheels.
Yeah. I read inboard for factory wheels and outboard for after market wheels.

I'm gonna have to flex my rear to ensure I can't snag my break lines.
05-28-2013 09:27 PM
JTPhoto JK This is not the proper way. But this is how the rear links are mounted when you have extended swaybar links and factory wheels.

If the upper bolt snaps the brakeline the bolt is too long.
05-28-2013 09:17 PM
Barmanvarn Thanks Viper...that's just what I needed. My install is the same as yours.

Here's the issue: There is another thread going on where a guy had the upper bolt snag his hard brake line and the line broke. There was a debate as to whether the link should be mounted inboard or outboard.

From what I can tell, I'm good w/ the TF kit as the new lower bump stop limits my travel to about 3 inches and the bolt is about 5 inches below the brake line with no flex.

Just a heads up in case this may affect you guys any.
05-28-2013 09:12 PM
ohioviper Took pic just now in the dark so best I can do for now.
05-28-2013 08:52 PM
Barmanvarn Don't ask why I need this, but can someone provide a pic of one of their rear sway bar links? I'm having a discussion as to what is the correct install.

Thanks
05-28-2013 08:49 PM
ohioviper So are you talking about unbolting the hard line from the frame bracket or unbolting it from the axle ?
05-28-2013 05:25 PM
whiteyjfm
Quote:
Originally Posted by ohioviper View Post
Even with the bracket unbolted the line offers no down travel that I can see .
Yes it does. Just unbolt it and zip-tie it to the shock if you want to be on the safe side.
05-28-2013 05:06 PM
ohioviper Even with the bracket unbolted the line offers no down travel that I can see .
05-28-2013 05:02 PM
JTPhoto JK The 2012 -13 JK have a bracket on the front brakelines that have to be unbolted. Older Jk don't have the bracket.
05-28-2013 03:20 PM
MichaelEdwardsDO Buy an anchor or a parachute just in case
05-28-2013 03:18 PM
Barmanvarn Same 2.5 lift here. I see no issues with drive line or front brake lines.
05-28-2013 03:01 PM
colbert1775 Running the same lift with the same worries my friend. I talked to my buddy who recently upgraded from the TF 2.5 to a 4 inch lift. He still runs his stock brake lines and disconnects when hes on the trails.
05-28-2013 02:58 PM
ohioviper
Terraflex 2.5 spring lift folks in here.

Ok some questions. I have the TF 2.5 spring lift and Ranchos 9000 shocks. The kit came with the brake line brackets which my guy installed on the rear but they do not work on the front. So as it sits I have the brake line drop brackets in rear and stock location in front. Im looking at running discos and need to know if I will need longer brake lines in the front and should I be worried about front drive shaft on 2.5" lift while discoed ? Is there anything else I will need to disco the front and get max flex on this lift ? Will the springs stay in place or drop out under full flex ?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:46 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC