Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > WF Local > WF Local Forums for Your Region and State > Tennessee Jeep Forum > Almost

Join Wrangler Forum Today


Thread: Almost Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2014 09:28 AM
jeeperdad1977 A mix of early 70s gm spindles n ford hubs changes to a 5 on 5.5 lug pattern. The guy I bought all that from also had spacers to convert the 5 on 4.5 rearend 8.8 to 5 in 5.5 to match which also spaced it out 1.25 inches on each side making it all real close. If your matching the same axles I have there is a super 88 kit for the 8.8 which adds width and offers axles drilled for either 5 lug pattern. Do your homework n ya can find plenty of options. Also by knowing whats going on with the build its less likely that someone will rip you off on bad work.
02-10-2014 11:21 PM
Barrettsyj What did you do about the lug pattern difference? And the width difference? Thought about this same set up.
01-25-2014 08:42 PM
jeeperdad1977 Well I haven't been to good at documenting this build or pics for it. But at the present I'm regearing the dana44 front. This is the first regear I've done n already 2 6 hr days into it. Today I finished my setup bearings and determined total shims on carrier. I did do an initial setup off my first figures. Everything looks good, backlash is .007. Pinion preload is on target and mesh looks good to eye. In the morning I'm gonna paint teeth and check mesh officially. If mesh is good is it as simple as same shims new bearings and then final check? I'd like some advice from experience and who might hear me in the morning ( not to early) if I have any issues or questions. This is the last step in my build for now. Ill be trail ready then. In the end I've got tj with 4" xflex lift. A rugged ridge SYE on my Tcase spins my 8.8 rear and the waggy D44 front. After tomorrow both will b spinning to 4.56 count from Yukon teeth. the front is hung in place by a totally custom truss and has mile markers hubs sealing the ends. The rear was already setup under a tj when I got it from J&J 4 wheel drive in Birchwood Tn so it slid perfectly under mine. Right now running some ford/dodge wagon wheels wrapped in 37 GY wranglers. I've been driving it for the last few weeks after the lift and axle swap. After hooking up the factory swaybar it handles great. I run with traffic even on the highways compfortably. I plan on welding the front diff since I've got manual hubs, does anyone have any negs on that??
12-08-2013 03:37 PM
jeeperdad1977 Here's newest add on. Got some rubi sliders n had this tube.

Attachment 575594
12-07-2013 12:49 AM
jeeperdad1977 Attachment 571234

Here's finished frontend.

Attachment 571250

This is the jeep done but not a good pic. Still some gearing issues in the front but not gonna pay for gear setup until I can afford an ox. I'm already regretting not going longarms n making plans to. Also starting to think about v8s and rollcages. I wanna keep it street able but have a feeling it won't be for long.
06-10-2013 06:59 AM
dabolt55 It's looking good man....
06-08-2013 06:24 PM
jeeperdad1977
Almost

Well it's almost done. I have a 2001 tj sport with 4" xflex lift, 8.8 rear, Dana 44 from 88 grand wag and 37" GY mtrs. Sye, 4.56 gears. I'm hoping to be rolling within the next month. I'm in Chattanooga n will make a couple test runs locally just to make sure she's good to go. After that I'd like to hit wind rock, wheeling in the country or Toms new park in South Pittsburgh. Anyone in the area or out of the area who's interested in getting a ride together let me know.

Attachment 259212

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 01:52 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC