|01-27-2014 06:48 PM|
|01-27-2014 04:38 PM|
Love it ! It was a breeze to install as well. I'm going to colour match the plugs and plate to the jeep once the weather warms a bit. Spot on kit though. Thanks loads
|01-19-2014 03:30 PM|
And for anyone else that is interested our Solution Plate is designed to work with both the horizontal and vertical vents on all JK models.
|01-19-2014 12:44 PM|
|_3m||Will this fit an 07 with the taller vent hole? I believe the o7- o9 models are 5 high x 2 wide later models have the 4 high x 3 wide vent openings.|
|01-08-2014 12:49 PM|
Thanks to Jason H. for this pic of his Dune JK running our complete LP relocation kit. Got all parts in stock let us know if we can get one headed your way.
|12-05-2013 01:50 PM|
Another customer pic using our Solution Plate, Complete plug kit, and an ORO tag/3rd brake light. Thanks for the pic Tom. We have these in stock and ready to ship.
|10-28-2013 01:44 AM|
Stumbled in here by mistake. Can't quite get how the stock one is in a bad place, and they look kinda wimpy without the spare really, but hey, to each their own I guess.
Just goes to show there is always someone coming along to take someone else's money.
|10-27-2013 05:09 PM|
The wiring on the ORO liteDOT is not plug and play but is about as straight forward as a wiring job gets. It comes with 3 wires in a pre-made loom, a (+) for the tag light, (+) for the brake/running light, and a ground. To make the install as clean as possible we run them through the tailgate,behind the plastic cover (on the inside of the tailgate), through the factory cloth wiring loom by the hinge, and then splice into the passenger tail light harness so there are no visible wires inside or outside. If anyone is ever installing one of these, whether they purchased it from us or somewhere else, feel free to give us a call at (909)-792-9777 and we will walk you through over the phone as best we can.
Here is a review from a customer of ours that was hesitant but ended up buying the ORO tag/3rd brake light.
"I purchased the plate and LED light a couple of months ago and love it. I considered not buying the light, because I get a little intimidated with wiring of any kind, super glad I bought it though. The whole install probably took me a little over an hour. I took my time to make sure I made it look as clean as possible and so I wouldn't have to tear it back apart later. The best write-up I found was on jk-forum, I'll try to link it. The only other thing I can think you'd need to know is that you'll want a decent drill bit to to make a hole in the license plate holder. This will allow you to hide the wire that comes out of the led. On a side note, I was able to visit the shop and was really impressed with the style and quality of all of their products. The owner Andrew spent a great deal of time showing me around, pointing out details of their stuff, and answering a ton of my questions. Good people to do business with.
|10-27-2013 07:49 AM|
|mack0092||What is involved in wiring up the license plate light/third brake light? plug and play?|
|10-26-2013 09:28 AM|
|Jeepers17||Just looked at your bumpers. That's one of the cleanest looks I've seen so far, front and back! those will be my next bumpers!|
|09-24-2013 02:40 PM|
We've had a lot of requests for the plugs to fill the holes in the tailgate and the factory license plate mount. We added an option for the license plate delete plug in the original post and from now on kits will come standard with the 3 plugs for the tail gate. If you have already purchased a kit previously and have not yet found a solution for the tail gate plugs we will make this retro-active so just give us a call and we will send the 3 plugs your way.
Full Metal Fabworks
|09-12-2013 02:14 PM|
here is a customer submitted pic of one done a little differently. She color matched her Solution Plate to her JK.
|08-27-2013 01:10 PM|
We added another option for a CB antenna mount that works well with the Solution Plate. The idea came from a member and it puts the antenna far enough towards the outside of the Jeep that its out of the way of the spare tire but far enough inside that it isn't constantly getting thrashed by trail obstacles. These are also $12 when ordered in combination with a Solution Plate. Details have been added to the original post.
|07-29-2013 12:04 PM|
Yes, we offer the ORO liteDOT tag/3rd brake light for this. It has 3 rearward facing red LEDs to serve as the 3rd brake light and 3 downward facing white LEDs to illuminate the tag. Let us know if you need a pic of the tag light at night and we'll see what we can dig up for you.
|07-28-2013 10:58 PM|
We also are a dealer for ORO and sell their LiteDOT LED license plate light and 3rd brake light that really helps clean up the back of our JKs.
|07-28-2013 09:56 PM|
|KnoXouT||Do you guys have a way to light the plate. It's state law where I live to have our plate lit at night.|
|07-28-2013 09:38 PM|
|Muddnuts1289||Full kit for 09' JKU shipped to 38671|
|07-23-2013 04:18 PM|
|07-12-2013 03:18 PM|
|07-01-2013 03:37 PM|
|Lusus_Naturae||Very clean. I would buy it except I always run a spare. I do like the bumper in the first photo too.|
|07-01-2013 03:19 PM|
All good points.
What I love is the thought and ingenuity that Jeep folks exhibit w/ their rigs.
You are a prime example.
Keep up the good work!
|07-01-2013 12:20 PM|
Some of them are:
1.) Weight Savings - some choose to leave the spare off to save the 130lbs or more that a 37,wheel, and carrier will add, especially on daily driven rigs where MPG is important
2.)Wheeling Locations - if you are wheeling Southern Style parks where you aren't more than a couple miles from your tow rig/trailer then its fairly easy to leave your spare there and if something happens have someone in your group run back and grab it (assuming it can't be fixed with a plug or patch and aired back up on the trail). Now if you are planning on driving to the Rubicon and camping half way through, then obviously going spare-less isn't as great of an option.
3.) visibility/departure angle- running a center mounted spare is going to affect 1 (or both) of these negatively no matter how you mount it, so if a spare is a must then some would rather have it mounted laying down out of the way behind the seats.
4.) Cost - For some people running a full size spare may not be an option when they first lift their JK. If you're running 37s or larger then its easily going to add $750-$1500 to the overall build cost between a 5th tire, 5th wheel, and a quality carrier that can support the new wheel and tire combo.
|06-28-2013 08:24 PM|
Looks great. However, am I missing something? Somehow I could never imagine traveling anywhere without a spare.
However, if I ever decide to roll with my spare on the roof rack I will look you up.
|06-28-2013 07:38 PM|
Thanks for the orders, and thanks to Jim V. for this pic of his Solution Plate that he integrated his LockPick backup camera into.
|06-12-2013 06:41 PM|
|FullMetalFabworks||Bump, Thanks for the orders. Still have a lot of these in stock and ready to ship.|
|05-24-2013 12:20 PM|
|tincinci68||You guys did it right. A lot better then the other companies...cough...spyder....cough....tera....cou gh....|
|05-16-2013 07:27 PM|
|shelbydog||That's a really cool idea. It really cleans up the rear end.|
|05-16-2013 06:23 PM|
|05-16-2013 05:55 PM|
That is very sharp. And welcome over here at WF.
What bumper is that on your first photo?
|05-16-2013 04:52 PM|
New solution to JK license plate relocation
Hello Fellow Jeepers,
We are Full Metal Fabworks LLC, a new vendor on the site. We know a lot of you frequent several forums, so you may recognize us from over on JKO. We have several products in the development process, but in the mean time we wanted to release a few of the products we offer to a new crowd and get our name out there a little more. Enough with the introduction, and on to the parts.
One of the first parts we would like to bring to market is The Solution Plate license plate relocation system. It’s no secret that the JK’s license plate is mounted in a vulnerable location and is prone to damage on the trails. For those looking to clean up the back of their JKs and ditch the extra weight of a tail gate mounted spare, the tire carrier mount provides a great spot to relocate your license plate.
The solution plate is laser cut from .090 aluminum and formed using a custom die. This forming process not only greatly increases the strength and rigidity of the plate, it also allows us to address a couple issues left untouched by existing license plate relocation systems in a single streamlined part.
The plate is dimpled out 7/8” to allow both horizontal and vertical vents to remain fully functional WITHOUT REMOVING THE VENT. This is important because it allows the cab to remain sealed from dust and water just as Chrysler designed it from the factory. A row of four laser cut holes along the bottom of the plate allow the vent to "breath".
It ships powder coated in a textured satin black finish,with (4) 1/4-20x3/8" stainless steel button head cap screws and (4) 1/4-20 top lock nuts for mounting the license plate, 3 plugs for the tailgate, and the solution plate itself mounts using the existing factory spare tire carrier mounting bolts and holes. We also are a dealer for ORO and sell their LiteDOT LED license plate light and 3rd brake light that really helps clean up the back of our JKs.
Solution Plate and hardware: $60
ORO license plate light and 3rd brake light: $40
Optional CB mount #1 powder coated textured satin black to match the solution plate:$12 when purchased with Solution Plate
Optional CB mount #2 powder coated textured satin black to match the solution plate: also $12 when purchased with the Solution Plate
License Plate Delete Plug: $18 when purchased with the Solution Plate ( solution plate comes with plastic plugs for the tailgate)
To Order Call: 909-792-9777 or shoot us a pm with a complete shipping address for shipping quotes.
optional CB mount #1:
optional CB mount #2:
optional License Plate Delete Plug: