Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Off Road and External Lighting > Electrical Wiring Assistance for Rock Lights...

Join Wrangler Forum Today

Thread: Electrical Wiring Assistance for Rock Lights... Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-21-2013 09:59 PM
BlueRidgeYJ Those lights only pull 6A when powered at 9V, your draw will be more like 4.5A at 12V.

Fuses go close to the power source (battery) and protect the entire circuit. Only one is needed per power leg, regardless of loads or switches in the circuit.

Either switch will work, but the fancier one will only carry 10A (vs 15A in the rocker). If you upgrade lights, you would need to use a relay switch or replace that switch to handle additional amperage.

That said, I would still probably use a relay to provide more direct power and remove the switch as a point of failure, though at that low amperage (<10A) it really is not required at all, as smaller gauge wire can easily handle that and run all over the place.
06-20-2013 12:39 AM
Boobooo good info dr_jenkem - and thanks for the pictures of your install.
06-19-2013 11:52 AM
dr_jenkem I used one fuse for switches on inside, and one fuse for each relay (rock lights/spot lights). I’m only using 3 cheepo floods now but the effect is cool and light the entry way pretty good. I’m using the factory looking switches as you mentioned, but don’t know if I care for them, the LED’s are not very bright and the light is inconsistent. Took one of them apart and adjusted the light, helped a bit. They do fit in the factory spot perfect but was thinking of trying the daystar type down the road.
If they really pull that much could just up to a 50 amp relay?

06-18-2013 06:29 PM
Electrical Wiring Assistance for Rock Lights...

First time doing electrical wiring so thought it best to ask for confirmation and recommendations on my planned setup.
I’m wiring in 6 rock lights. Each light will pull about 18 watts and 6amps. 18W Bolt Rock Lights ( 3 Pair )

Would it be better to split them up into two separate connections by attaching 3 of the lights to a 40amp relay (12 VDC Waterproof 5-Pin Relay SPDT 30/40A with Metal Bracket 330-079)
And use a 20 amp fuse (In-line ATO/ATC Fuse Holder 10 AWG 070-675)
Connected to a switch inside the cab?
Or is it safe to wire them all together to the same switch with a larger fuse?

Also – for the fuse – do you fuse the connection between the light and the relay or the relay and the switch? Or both…

Haven’t decided yet on the switch…

Hard to justify the cost of these but they look cool- Plasmaglow 11010 Blue Stainless Steel LED Activator Switch (On/Off Version) : : Automotive
May just go with standard factory lookalikes - Rocker Switch 315 12 Volt Rock Light TJ Jeep Wrangler 96 06 Driving Spot Rock | eBay

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 09:49 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC