|06-18-2013 11:38 PM|
Also as for the total hieght issue, there was a thread that came out before that talked about it, I believe I actually posted my height too (I got about 1.5 inches of clearance in my garage, and that was after I adjusted the stops on the garage opener to make it open up all the way!). There is a formula for it, it goes something like this:
The stock jk is 70.9 inches high with 31 inch tires, 69.9 with 29s, and 71.4 with 32s (don't quote me on that, it of course depends on what kind of weight you have and how much tire pressure you're running) but it's pretty much that). So lets halve the tire diameter and subtract it to give us a base line, it's about 55.4.
base line is 55.4
Tire diameter in inches is T
lift size in inches is L
JK height in inches is H
H = 55.4 + 1/2T + L
|06-18-2013 04:43 PM|
|06-18-2013 04:06 PM|
Automotive Driveline drive shafts.
BTW, I found the before/after measurements. It went from the highest point before of 72" to 77". The 35" Toyos measured 34" mounted. Go figure.
|06-18-2013 03:34 PM|
Which driveshaft you go with UTJD?
|06-18-2013 02:40 PM|
You should be okay getting it into the garage. My JKUR has a 3.5" DS AEV lift w/35" Toyo M/Ts and it fits fine with either the hardtop or soft top. I, too, replaced my drive shafts, as one boot got punctured when rock crawling the first time out.
Had MT/Rs before. Got Toyos this time b/c the Goodyears were on back order, but I've been very happy with the Toyos. They don't seem to chunk as much as GYs on the rocks, IMO.
|06-18-2013 01:10 PM|
Good point. I do have a TeraFlex exhaust spacer. But I think its a little shorter than yours so yours must get it out of the way more. That does bring up the point you can also re-route your entire exhaust as an alternative.
I'll be replacing the drive shaft- gives me a beefier one and gets rid of the plastic boot. One less thing I have to worry about breaking while rock crawling. The benefits outweigh tinkering with the exhaust for me. (But $40 is cheaper than $500).
|06-17-2013 11:45 PM|
I've been running this on my 2012 with a 4" lift off road for quite a while now with no issues:
Jeep JK Wrangler Exhaust Extensions
|06-17-2013 10:51 PM|
|AGGIE_Rubicon||Hmmm...so it really is just a slight difference in how they are made but I can see why if I were going with a 3.5" it could make it or break it. I am considering either the Toyo MTs or the Goodyear MTRs I ordered my wheels but still havent ordered the tires because I can't decide. (I wasn't going to install them until i did the lift anyways) I am ordering the lift the first of next month so I guess I better make up my mind.|
|06-17-2013 10:14 PM|
I started with Toyos- never installed them. Swapped for 305/70 KM2. Re-geared and switched those for 35" (true) MTRs.
|06-17-2013 10:11 PM|
|spieg||A little late to the party, but my '13 jkur with aev's 3.5 RS sits around 77" in the rear with no top, stock bumper / no spare, and 315 70/17 duratracs.|
|06-17-2013 10:00 PM|
|AGGIE_Rubicon||Well I have made up my mind I am just going to play it safe and go with the 2.5 lift. Would someone explain this tire height thing to me. Why are there differences in height with the same size but different brand?|
|06-16-2013 05:10 PM|
My stock height is 70" so I dont know about that one.
|06-16-2013 02:39 PM|
74" to 74.5" (sloped driveway). 3" Mopar, 35" MTRs. Lotsa armor; front bumper, winch, TF rear tire hinge. Bad shot but all I have with new 35s.
Don't forget there is a big difference w/tire height. A 35" MTR will be taller than a 35" KM2 for instance.
|06-16-2013 01:39 PM|
|06-16-2013 01:36 PM|
My unlimited is 78" with the softtop on 3.5".
|06-16-2013 01:33 PM|
|JeepHerz||Have you considered your driveshaft? Anything above 2.5" and you'll have geometry issues. The pic below is my driveshaft boot sitting on my exhaust (that is at full droop FYI). Not good. If you're Jeep is a DD only maybe you'll be okay and you won't hit much. But for me it's $500 for new driveshafts- not chancing it. If I didn't rock crawl and weren't accident prone I'd do 2.5" and call it a day. You can still do 35s, look good, be capable and save yourself some trouble. Oh and fit in your garage.|
|06-16-2013 01:14 PM|
|06-16-2013 01:23 AM|
|Dubler||Call the lift company. I did. According to AEV I could fit a 3.5 lift in my small ass garage (72")|
|06-15-2013 08:00 PM|
|AGGIE_Rubicon||I just thought I would include a few before and current pictures to say thanks for the help. I will have more to come soon I am planning on the lift and tires the next month.|
|06-15-2013 07:42 PM|
|AGGIE_Rubicon||Great information guys and thanks for taking the time to measure and respond. I have 82.5" if you include the concrete lip so I should be just fine with the 3.5 also considering I have full front and rear bumpers with tire carrier and a winch on the front. I think I am going move forward with the 3.5" lift. I just have to be able to fit in the garage because I am planning on putting company logo decals on my jeep and my HOA doesn't allow them if not in the garage. if all else fails I can leave the logos off if it comes to that.|
|06-15-2013 10:26 AM|
|SBL||I have a 13 rubicon with a 2.5" AEV lift and 315/75/17 duratracs on stock rubi wheels. I am right a 77" with the soft top on but if I am in sunrider mode I am just under 81". My garage door at my house is 82" so it is tight.|
|06-14-2013 08:46 PM|
|dwindeck||I run a 4.5 AEV and 37" KM2's and a hard top. Standard door height and mine clears with at least 3", I also store my buddies...AEV 4.5" 37 MTR's (1/2" taller than the BFG's) with a soft top which is higher than a hard top, his has a couple inches to spare. We both have front/rear bumpers tire carrier's, winches ect which weight them down a bit. You should be fine.|
|06-14-2013 08:34 PM|
I have 35s (effective height is 34 1/8") and Rubicon Express 2.5" and my Jeep is 6'3"
FYI no 35" tire actually measures 35" in height
|06-14-2013 08:17 PM|
You will be fine if your garage is a true 84". Was in the same boat as you debating but my garage is 77.75" when you factor in the trim and the lip on the cement. So, I'm doing a 2.5 game changer. Had 5.5" clearance with hardtop and 60" rear springs. I'm on 35's (duratrac so small diameter compared to other brands) now, no lift while awaiting delivery of it and currently have 4.25" clearance. The 2.5 GCL should give me an inch or so to spare (lite jeep so I'll net more than 2.5) and have probably 3 - 3.5 added height. I would have gone 3.5 but wasn't into airing down or modifying the garage. Parking outside wasn't an option because our driveway is single lane and splits at the end to our 2 car garage. Work car stays on the street already. So, your only choice now is what lift since you'll clear either.
Edit, just make sure you have 84" because my garage opening is over 80" but once you measure the true opening as the vehicle pulls in its considerably less. Also make sure you take multiple measurements along the garage as I found one side of mine to be a full inch and a half taller.
|06-14-2013 08:06 PM|
|AGGIE_Rubicon||Thanks for the response my garage has exactly 7ft high entry way so I need to stay below that. So if someone with the setups can take a measurement I would love to see what you have. I dont want a moment.|
|06-14-2013 12:22 AM|
|rijowysock||would depend on garage height, most doors are 7', my 997+bike is over 7'.. i would assume a JK with 3.5" and 35's would be damn pushing it.|
|06-13-2013 11:56 PM|
|ThatWhiteMachine101||Gotta buddy on 3.5" lift and 35s, fits in the garage.|
|06-13-2013 11:52 PM|
|Tweak||im on a 3.5 RK lift (so probably 4.5in) on 37" tires and its just over 6 foot 4. barely fits in the garage.|
|06-13-2013 11:23 PM|
|AGGIE_Rubicon||Bump still looking for help|
|06-11-2013 11:13 PM|
Total Vehicle height after 2.5 & 3.5 lift with 35x12.5R17
As the title says I am looking at getting a lift with 35" tires and I can't decide 2.5 or 3.5 in lift. I would like to have the 3.5 but I MUST be able to fit in the garage. So if anyone would mind taking a measurement from the ground to the top rear corner with the mentioned setup a I would appreciate it. Would you also please include the brand and size of both lift and tires. Thanks for the help I am really enjoying the forum