Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Adjusting clutch pedal

Join Wrangler Forum Today


Thread: Adjusting clutch pedal Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-27-2013 08:39 PM
jkjeeper06
Quote:
Originally Posted by Bullfish View Post
Please excuse my ignorance on this topic, but I always thought you 'should' put the clutch all the way down to the floor regardless. I always thought if you didn't you might damage something. But if all you need to do is hit the engagement point, then shift, that is cool. lol
On a hydraulic clutch the clutch is disengaged before it hits the floor so all you have to go is get past the engagement point and shift. I get it almost to the floor if not all the way just because I've always done it and on my other cars its more important
06-27-2013 07:46 PM
Bullfish Please excuse my ignorance on this topic, but I always thought you 'should' put the clutch all the way down to the floor regardless. I always thought if you didn't you might damage something. But if all you need to do is hit the engagement point, then shift, that is cool. lol
06-27-2013 06:28 PM
josea1952 So, I just placed a spec 3 in my 08. Has anybody entertained spacing the slave cylinder out with collars or a spacer to bring the pedal down to a reasonable normal car level?
03-08-2013 01:54 PM
Billet13 My '13 engages pretty high up as well. Very different than anything I've had before, but I'm getting used to it. Take it in and have it checked. Drive another one while you are there. I bet it's about the same...
03-08-2013 01:04 PM
SilverSport
Quote:
Originally Posted by Greg__Berger View Post
Really? I find that I've got to put mine way down. I know it's not a sports car or anything, but it's really crunchy and I've even heard a little gear grind in the past couple of weeks if I don't have the clutch depress almost all the way. Thinking about swinging by the stealership and having them drive it. Maybe I'm just being paranoid.
I had the crunchiness and it has nothing to do with the type of transmission and it's not a Jeep thing. It also has nothing to do with your shifting habits.
For the cause look at post #49 in this thread: http://www.wranglerforum.com/f33/man...ml#post3426620
03-08-2013 12:59 PM
Greg__Berger Thanks for the input! I've been trying to keep it slow and pause for the synchros, but maybe it's not slow enough
03-08-2013 11:38 AM
TrueNorth I had my clutch and throwout bearing replaced at the dealer under warranty recently. Throwout bearing failed at 40K.

Picked it up and promptly killed it twice in a row before I even left the dealer lot!

Grabbed so high in the travel and so suddenly I could barely drive it.
After a couple thousand miles it broke in and feels normal now.
Starts to engange a couple inches off the floor and doesn't grab suddenly anymore.

My assumption is your 13' clutch plate is just new, thick and sticky.
It will soften up over time and become predictable. Give it a couple months.

+1 on the quick shift grind, especially 1st to 2nd. I've learned to just slow it down and give the syncros time to mesh.
03-08-2013 11:24 AM
onetraveller As mentioned all clutches are a little bit different. Drive it for a few months and your driving style will adapt to the clutch.

If you are getting a grinding sound when you shift, slow your shifts down. This a heavy duty truck transmission, not a race car. Shift in two distinct phases, phase one disengages the clutch from its current a gear, now pause for about half a heart beat, phase two moves it into the new gear. The pause is short, but important. It allows the synchros time to align.

Mike
03-08-2013 09:57 AM
Greg__Berger
Quote:
Originally Posted by Casotakar1229 View Post
weird, I hardly have to press my clutch on my 12. just bend at the ankle, don't even push with my entire leg. only on start up I have to press quite a way.
Really? I find that I've got to put mine way down. I know it's not a sports car or anything, but it's really crunchy and I've even heard a little gear grind in the past couple of weeks if I don't have the clutch depress almost all the way. Thinking about swinging by the stealership and having them drive it. Maybe I'm just being paranoid.
03-07-2013 09:59 PM
Casotakar1229 weird, I hardly have to press my clutch on my 12. just bend at the ankle, don't even push with my entire leg. only on start up I have to press quite a way.
03-07-2013 09:30 PM
SilverSport
Quote:
Originally Posted by Blastek View Post
^as far as i'm aware, the hydraulic system for the 6-speed is a sealed unit and meant to be replaced as one piece.
Parts are available individually.


Quote:
Originally Posted by Blastek View Post
the high biting point is completely normal on the JK. That doesn't indicate whether it's worn or not. As the friction material wears, it will adjust so the bite point doesn't change.

I believe the warranty only covers the clutch for 1year/12k miles.
Yup. 12mo/12K miles.
03-07-2013 05:01 PM
Blastek
Quote:
Originally Posted by JKjingle View Post
I thought my clutch was wearing prematurely because it was activating up top too. Took it to the dealer they said its fine... Don't know if I believe them or not but its got 5 years warranty and if that clutch dies earlier than it should I will be pissed. There's no way to inspect without removal they just drove it a few blocks. Maybe I'm just paranoid it could be just breaking in.
the high biting point is completely normal on the JK. That doesn't indicate whether it's worn or not. As the friction material wears, it will adjust so the bite point doesn't change.

I believe the warranty only covers the clutch for 1year/12k miles.
03-07-2013 04:55 PM
JKjingle I thought my clutch was wearing prematurely because it was activating up top too. Took it to the dealer they said its fine... Don't know if I believe them or not but its got 5 years warranty and if that clutch dies earlier than it should I will be pissed. There's no way to inspect without removal they just drove it a few blocks. Maybe I'm just paranoid it could be just breaking in.
03-07-2013 04:30 PM
Blastek ^as far as i'm aware, the hydraulic system for the 6-speed is a sealed unit and meant to be replaced as one piece.
03-07-2013 04:08 PM
Matches I am a mechanic (retired) and I'll tell you not to touch that system on your 13. If there is a problem it is still under warranty. In all likelihood there is no air in your system. Every clutch is a little bit different and will have different release points. If there is air, something in the system is defective and will be replaced under your warranty. If you touch it and break something its your baby. Its very easy to turn something the wrong way bleeding if you are not accustomed to it.
03-07-2013 03:53 PM
Rooster76 On my 2012 it engages about half way. I'm not a mechanic, but will try to help you take a stab at your issue. Its my understanding that the clutch is run off the hydraulic "master cylinder" along with the breaks. My guess is that you need to bleed your clutches slave cylinder (that gets its fluid from the master cylinder) to get any air out that would cause it to engage further down. Here are the parts involved.

MASTER CYLINDER
The master cylinder is just under the master cylinder reserve. Its on the driver side under the hood.

(image from HowStuffWorks "How Master Cylinders and Combination Valves Work" )
You fill the reserve with DOT 3 break fluid (or what ever the cap says). It's important that this doesn't go dry during the process and allow any air into the master cylinder it feeds. Here is a picture of the reserve being filed (from> MAINTENANCE : Bleeding the Brakes on a Jeep JK Wrangler )


SLAVE CYLINDER

The slave cylinder is on the driver side of the transmissions bell housing. Bottom of the Jeep under the driver door.

This is the part slave cylinder your looking to bleed.
(image from How do you bleed the clutch?? - JeepForum.com)


This is a new slave cylinder

(image from >
Centerforce Clutch Install This thread shows what the slave cylinder looks like and says it was hard to bleed but not much else.)


(Image from slave cylinder - JKowners.com : Jeep Wrangler JK Forum
This thread doesn't tell much about bleeding the slave cylinder but does show it attached.)

STEP BY STEP
So that's the basic parts involved in tightening up the clutch pedal if my hunch is correct, and it is air in the system. There are links that go over the step by step of the bleeding process.
LINK> How To Bleed A Hydraulic Clutch On A Jeep Wrangler
LINK> 6 Speed Owners!
03-06-2013 11:53 PM
rfletch1 thanks man, i appreciate the info
03-06-2013 11:39 PM
Blastek Nope, it's a hydraulic system. Unfortunately, there's no way to adjust the engagement point (at least not easily).
03-06-2013 11:21 PM
rfletch1
Adjusting clutch pedal

Hey everyone,

I have a 2013 wrangler sport and the clutch pedal has to be depressed about 80% of the way before it engages. Is there anyway to adjust the pedal to where the clutch engages about half way. Im new to the wrangler and manual transmissions so I apologize if i sound like an idiot.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:00 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC