Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Builders Corner > Adams Drive Shaft Install

Join Wrangler Forum Today


Thread: Adams Drive Shaft Install Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-30-2013 01:19 AM
wmwhitey
Adams Drive Shaft Install

I will start by saying sorry for no pics I might put some up later. The reason I am writing this is cause there are no instructions that come with the drive shaft and nothing I could find online on it either.

TOOLS YOU WILL NEED
1. 150 torque wrench
2. 1 1/4 deep well thin wall socket
3. 5/15 wrench
4. 16 MM
5, 17 MM
6. 4" pulley puller
7. Loctite of choice I LIKE BLUE
6. Silicone
7. I am sure I missed a tool or two but a basic socket set will get this job done.

REMOVAL
1. Chalk the tires set the Emergency brake.
2. To make life easy remove the transfer case skid.
3. Brake loose all the bolts on your OEM drive shaft, there are 4 at the axle and 8 at the transfer case.
4. Lift the front of your Jeep and put your 4wheel drive in neutral.
5. Start with removing the 8 bolts that connect the drive shaft to the yoke.
6. Move to the front Remove the 4 bolts at the axle.
7. Your OEM Drive Shaft will come rite off now.
8. You now have to remove your OEM yoke.
9. 1" 1/4 nut is inside your yoke you need to remove that to pull the OEM yoke off.
10. If your yoke will not slide off you can use what I used and that was a 4" pulley puller popped it rite off.
11. There is a small rubber ring in your OEM yoke you need to pull it out and install it in your new yoke. Put a small amount of silicone on the ring and slide it in your new yoke.


INSTALL
1. Slide your new yoke into the transfer case. Tighten the nut down with the torque wrench to 150LB.
2. Insert your new drive shaft start with holding the front up with two bolts at the axle "don't tighten down yet they are just there to hold your drive shaft in place for now".
3. Use the 5/16 wrench and install the 4 supplied bolts with the new Drive shaft at the yoke. "start all 4 bolts use loctite if you want I suggest you do and tighten the bolts down evenly".
4. Move to the front and install the 4 OEM drive shaft bolts "use loctite again and tighten down evenly".
5. Lower the jeep down on the ground start your Jeep and put the 4weel drive in gear.
6. Return under the jeep and tighten all bolts down again.
7. Install your transfer case skid.
8. Your done go test it out here is the thing if you dont tighten all the bolts down even you will get a bad wobble and you will think your Jeep is jacked up.


Dont be rude if I missed anything just trying to help others out.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 04:54 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC