|07-05-2013 08:49 PM|
I used a BlueSea SafetyHub 150 in my Jeep for the accessories. I hooked up the H4 upgrade, my stereo amps, Hella horns, etc to it. Still have room for lots more I wanted room for high and low draw items so went this way over the Spod which is for lower draw (3-15A + 3-30A) max per cicuit/50A for the whole panel. I do want to make a Spod style switch panel though when I get a few more things in the Jeep to keep it looking good, but that wouldn't be too bad to make myself either.
|07-05-2013 08:36 PM|
+1 on adding your own fuse block. BlueSea Systems (http://www.bluesea.com/products/category/Fuse_Blocks) makes some water, uh, 'resistant' blocks. Click on 'ato/atc' blocks on the link for automotive type fuses. (Amazon also has em)
I use the previously posted part store available 8$ block for my accessories; it is exactly what I need, as safe as low-voltage electricity can possibly be, and cost me about 100$ to add several relays, OFC wiring, multiple fuse hookups, switches, and a custom switch panel. And probably still had a steak dinner when I was done.
If you need help designing a schematic, just ask. There's lots of sharp cookies on WF.
|07-05-2013 03:37 PM|
1) how much stuff do you plan on hooking up? 2-3 things... probably not worth doing either solution.
2) how much time do you want to spend setting all this up? not much...get the sPOD
It's a nice piece of equipment, and adds more protection than just a simple fuse block. Not necessarily needed, but you're not wasting your money if you get it and plan on hooking up a variety of things. The best part is that once you have it installed, all the accessories you add later go on in no time at all and you have all the switches pre-wired with a nice OEM look.
|07-05-2013 03:27 PM|
Thanks for the replies guys.
KaiserJeep, where did you find these parts and would you please provide a couple of pics for your install? This is certainly a lot cheaper way to provide a safe electrical aux power.
jp2611, I am definitely NOT an electrician (obviously), but what does it hurt to ass electrical components as long as you do not run too many at one time? I think that is where I was going with my original question.
An additional question I have is at what point do I need to add an additional battery and how is it installed?
|07-05-2013 05:17 AM|
The OP question was do I HAVE to add an Aux power dist. no you don't have to....same as you don't have to add fuses and relays to wiring circuits...but depending how many circuits, the load and the environment that your Jeep is used in you may or may not have a Fire or other issue.
From what you were saying the start of the thread....IMO it is time to add an Aux Dist. board of some sort or stop adding electrical components.
|07-05-2013 03:50 AM|
What I did as part of my dual battery install was buy three of these Bussman automotive fuse blocks ($8 each):
One is mounted under the hood, one is mounted in the glovebox next to the stock fuses, and one is mounted in the rear Add-A-Trunk. I connected them with a 4-guage wire to the battery switches, and run the power to the 4-guage wire through a single 140-amp main ANL fuse and fuse holder:
...everything else is just wires with battery lugs crimped on the ends. My total investment was less than $50 on these three fuse blocks.
To add a circuit, all you do is select a blade fuse of the correct size for the load, and plug it in one of the fuse block slots. The fuse energizes the adjacent spade lug. I do not have to run more than about 4' of power wire to reach any part of the Jeep from one of these fuse blocks, very convenient. The three 8-circuit fuse blocks allow me to add up to 24 auxilliary circuits.
|07-04-2013 10:11 PM|
|Rotornut||Kinda looking for some help here fellas. Anyone?|
|07-04-2013 09:59 AM|
|Rotornut||hmmm? No opinions?|
|07-03-2013 05:48 PM|
Aux Power Distribution System???
Do I REALLY need to add an Auxiliary Power Distribution System (like the S-Pod) valued up to $500 to my '02 TJ? Seems a little...........expensive?
I have Aux Bumper lights and wanting to add an on board air compressor. I have a winch, but use it with the clip in hand controller.
Maybe I'm wrong. Can someone jump in here and convince me to spend that kind of $$$$?