|08-16-2013 08:38 AM|
The guy told me that he update the software in the ECU and they cleaned the o2 because we put new original mopar o2 and still the same codes.
So what they did and now the jeep runs better than ever.
Cleaned all the connections
An that was it.
But they told me, that if the MIL comes back on i will need to change the complete ECU because it wasn't reading the two upstream o2s
So far 700miles and still no mil.
Hope that was the problem
|08-15-2013 06:32 PM|
Well, what was it?
|07-24-2013 12:16 AM|
|jeepstertj||Jeep is right now with the dealership. 5 mechanics couldn't find a fail with the o2 they are working perfectly. There isn't a exhaust leak. The dealership expert told me that the ecu is receiving a false signal and thats is the problem why? Where? Im gonna keep you updated as soon as the jeep gets fixed.|
|07-19-2013 07:58 AM|
|jeepstertj||Ok i will do the trip and later change the o2's i will keep you updated as soon as i get it fixed!|
|07-19-2013 06:23 AM|
Shouldn't be an issue short term, but long term ( many many miles) running with failed 02 sensors will hurt fuel consumption. It's a $70 part ( in the US), just change it and see. If you have a digital multimeter and a service manual, you can at least check the low end (cold state) output signal.
|07-18-2013 11:30 PM|
|amiller||Mine were reading slow too. My 05 had bad catalytic converters at 20,000 miles... Hole burned clean through the catalyst. It still ran fine too.|
|07-18-2013 11:23 PM|
Could it be a problem if a make a trip tomorrow with those codes? Its gonna be 600 km round. But im gonna tow my boat.
|07-18-2013 09:50 PM|
|07-18-2013 08:46 PM|
|jeepstertj||Codes are back!!!! Same codes. Engine still runs fine and i couldnt find any other exhaust leak!|
|07-18-2013 12:29 PM|
Thanks for your help. Well right now im searching for the leak. So far the bolts were pretty damn loose. Not only the bank 2 the bank 1 was almost coming of. So i think this should fix it. I did torque the exhaust manifold bolts also and they were tight but the bolts before the first 2 cats where the problem. Im restarting the ecu. And so far the exhaust sound changed alot! But still im searching for another leak just in case.
|07-18-2013 11:27 AM|
|TCogley||if you have an exhaust leak then its very possible that leak is causing the o2 sensor lights to come on, the exhaust gas is escaping before it reaches the o2 sensors throwing the readings off and causing the engine light to come on. id recommend fixing the exhaust leak and resetting the light|
|07-18-2013 11:06 AM|
Do a search. http://www.wranglerforum.com/search....archid=8918377
|07-18-2013 11:02 AM|
|07-18-2013 10:36 AM|
Update yesterday i reset the ecu and today is back on with both codes p0133 and p0153.
What to do???
|07-17-2013 01:52 PM|
MIL on? Exhaust thread
My 06 rubi started normal to give the check engine light 3 weeks ago. At first i was wheeling and in the middle of the night when i was coming home, and suddenly the MIL came on. I did the key trick and it was code p0153 o2 sensor bank 2 sensor 1 slow response. So i reset the ecu to check it.
And yesterday it came back on but now with the code p0133. O2 sensor bank1 sensor 1.
And im checking the meaning and its exhaust leak or poor performance of the o2.
What do i know so far is that indeed i have a exhaust leak but its on the second header where the header connects to the doughnut and the catalytic converter.
Could this be the fail? Engine still runs pretty fine no mpg increase great power as always.
But im thinking to tighten the bolts they might be came loose. But i heard that they can break very easily.
Should i do it? What else do i need to check?
I cant belive that the o2 sensor are going bad my jeep only has 52312 km.
Thanks for your help