Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Jeep Discussions > Communications and Electronics > Rip and replace stereo plan

Join Wrangler Forum Today


Thread: Rip and replace stereo plan Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-25-2013 03:53 PM
ChasUGC I would get everything at once and complete it in one install. Constantly removing the dash, is going to weaken the connectors to the console, cause them to bend, and ruin them. Then, constantly pulling and changing the wires could lead to a short. Just do it once, get it right the first time, and this is best.
08-15-2013 10:11 AM
Mattk11
Quote:
Originally Posted by ND Irish JK View Post
I thought about getting a cover for the cargo area when I take off the top to prevent it getting wet, but to also cover up the subwoofer.
I had one on, but the way I designed it, it had a 1" space between the cover and the tailgate bar so I can put on the soft top on. I thought it would keep out most of the water, but it all seems to go right to that storage box.
08-15-2013 06:50 AM
ND Irish JK
Quote:
Originally Posted by Mattk11 View Post
Be careful, I got caught in a little rain with my top down and didn't think much of it, it was sprinkling. My rear carpet was a little wet but dried by the next day. About a week later I opened up my rear cargo to grab some jumper cables and it was filled to the brim with water. Not a great environment for electronics.
I thought about getting a cover for the cargo area when I take off the top to prevent it getting wet, but to also cover up the subwoofer.
08-15-2013 06:48 AM
ND Irish JK
Quote:
Originally Posted by woansleftpeg View Post
Just hot.
Actually, no. The amp has a built in fan, and the cables are routed in through both sides so it props up the door enough that heat does escape. I have checked the temp of the amp multiple times and it is cool to the touch even after being on for over an hour.
08-14-2013 05:34 AM
Mattk11
Quote:
Originally Posted by ND Irish JK View Post
I just replaced everything this past weekend. I installed my amp in the hidden cargo tray in the rear. That way I don't have to worry about it getting wet, or dirty.
Be careful, I got caught in a little rain with my top down and didn't think much of it, it was sprinkling. My rear carpet was a little wet but dried by the next day. About a week later I opened up my rear cargo to grab some jumper cables and it was filled to the brim with water. Not a great environment for electronics.
08-13-2013 10:50 PM
woansleftpeg
Quote:
Originally Posted by ND Irish JK View Post
I just replaced everything this past weekend. I installed my amp in the hidden cargo tray in the rear. That way I don't have to worry about it getting wet, or dirty.
Just hot.
08-13-2013 07:13 AM
Mattk11
Quote:
Originally Posted by WhiskeyMike View Post
Awesome, thanks. What subs did you put under the seats? Do you have any pics?
Sundown SD-2 10" under each seat. I've also made a few others with Alpine Type R, Rockford Fosgate and JL shallow mounts. Then I retired from the box building business. Too time consuming and I didn't really make any money.

Attachment 285285



Attachment 285286



Attachment 285284
08-12-2013 11:16 AM
ND Irish JK
Quote:
Originally Posted by WhiskeyMike View Post
Awesome, thanks. What subs did you put under the seats? Do you have any pics?
I just replaced everything this past weekend. I installed my amp in the hidden cargo tray in the rear. That way I don't have to worry about it getting wet, or dirty.
08-07-2013 07:41 AM
WhiskeyMike Awesome, thanks. What subs did you put under the seats? Do you have any pics?
08-07-2013 07:25 AM
Mattk11
Quote:
Originally Posted by WhiskeyMike View Post
I've got everything on order for a total rip and replace of my stereo and I plan to do it pieces. Please let me know if you see any issues or extra items I'd need to do it this way.

First replace headunit, use harness and steering wheel packages, run stock speakers through harness. Test.

Then change out all 6 speakers. Test.

Then add amp, switch speaker wires from harness to new runs going to amp, capping harness speaker wires. Test

Then add basslink. Test. Then backup camera.

My thought is that this allows me to do it piecemeal so I know all the pieces are working in stages, as opposed to ripping everything up and praying. I also thought about using a measuring app on the ipad to track the differences. It's not a solid way to know which sounds better, but which is producing the broadest hertz ranges. I don't see much rework in this process.

I haven't installed a radio in 20 years, so I think slow and steady is best.
Radio replacement is easy and won't take you long. While you have the center of you dash opened up, you may want to run the wires for you amps (RCAs, turn on wires) and leave them there until you are ready to install the amps.

You can do all 4 speakers on the same day. The front speaker pods aren't as bad as people suggest. The passenger side is easy - take it out through the glove box opening. The drivers side takes more time and guts because you have to pull out on the lower dash to the point of it almost breaking and tumble the pod forward and out. The tweeters are simple and the sound bar even easier. Of course if you plan to run new speaker wires with the new amps, you will have to repeat these steps again.

Amps will depend on where you put them. If you plan to use the factory location, do it while your speaker pod is out or you will just have to repeat the process. Some people put them under the seats, but I ultimately used that space for subs. I put all three amps inside the dash since there is quite a bit of room up there if you get a little creative.

I will say this, if you budget 4-6 hours for each stage, it will take you double because of little snafus like connectors, wire routing, trimming and connections. And if you do it piecemeal, you will be doing your teardown and rebuild multiple times in some cases because of access. I bet I have pulled my radio 5-6 times as I changed, added and tweaked my system

Your method works fine if you don't mind tearing apart, testing, tearing apart again, re-testing, tearing apart again, etc. I did mine all at once. Jeep was torn apart for two and a half straight days in late December. Once all the wiring was done, I built the sub enclosure and added the sub (just had to connect the speaker wires). I have since redone the subs, put in a larger sub amp and then added a second sub and second sub amp. Third time around was a charm and I learned a lot in the process.
08-05-2013 07:52 PM
WhiskeyMike Yep, I hear ya.
08-05-2013 07:05 PM
Neral22 The dash for the front speakers is a real PITA so just dont put the dash back together in between the stages
08-05-2013 06:20 PM
WhiskeyMike
Rip and replace stereo plan

I've got everything on order for a total rip and replace of my stereo and I plan to do it pieces. Please let me know if you see any issues or extra items I'd need to do it this way.

First replace headunit, use harness and steering wheel packages, run stock speakers through harness. Test.

Then change out all 6 speakers. Test.

Then add amp, switch speaker wires from harness to new runs going to amp, capping harness speaker wires. Test

Then add basslink. Test. Then backup camera.

My thought is that this allows me to do it piecemeal so I know all the pieces are working in stages, as opposed to ripping everything up and praying. I also thought about using a measuring app on the ipad to track the differences. It's not a solid way to know which sounds better, but which is producing the broadest hertz ranges. I don't see much rework in this process.

I haven't installed a radio in 20 years, so I think slow and steady is best.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:07 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC