Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Opinions on this frame rust

Join Wrangler Forum Today


Thread: Opinions on this frame rust Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-08-2013 02:38 PM
Bet What's the easiest way to get to the rear cross member, near the rear shocks? It's starting to bubble.
09-07-2013 06:23 PM
Gixxer86g You should pay close attention to the bolts holding your skidplate on. A couple of weeks ago, the right side broke loose on the trail. The center and rear bolts were gone, and the front pulled through the frame with the nutsert.

My frame looked better than yours from the outside, but in reality had similar rot in the same spots. You may find that when you get the skidplate down, that new nutserts will be out of the question due to rot.

If that's the case, check out replacement frame caps from Autorust. I just installed the center skidplate sections on my 98. It was a big job, but it isn't rocket science. All you need is average welding skills (or a friend with these skills).

My biggest concern now is the sections on the rear of the frame near the control arm mounts (the front ones).

I POR-15'd the center sections and used Eastwood's Internal Frame Paint on the entire frame. I'm hoping the internal treatment will buy me time on those rear sections.
09-07-2013 02:36 PM
Alleyway Sandblasting is the best way to remove the cancer.
09-07-2013 10:37 AM
1jeeplvr It really doesent look that bad.Make sure you really inspect all of the frame.Mine was 110% worse when i decided to swap the frame out.
09-07-2013 02:44 AM
MarkGLHS agree, that is bad but repairable......wire wheel all the exterior rust, if you have a rifle cleaning kit use one of the wire brushes to get inside the frame and loosen up the rust.....then use a flexible tube attached to a shop vac to thoroughly vacuum out the inside of the frame. hit the inside with Eastwoods Internal Frame Coating and POR-15 the outside.

one more thing: drill a few holes on the underside of the frame to allow water to drain out and to allow additional places you can vacuum out the interior of the frame.
09-06-2013 10:43 PM
GingerTJ Mine is worse.. But still no failures. Wire wheel it and roll it with por15 or bedliner.
09-06-2013 10:32 PM
Shoe The bolts that hold the skid plate on are called "nutserts". If they just spin instead of coming out then you will have to cut them off and replace them. Getting them back in is easy if you can get them off! Do a search on nutsert replacement and you should find lots of good info.
As far as the rust it looks like worse than just surface rust but not too bad yet. Take care of it now and you should be good for years.
09-06-2013 09:40 PM
Bet
Opinions on this frame rust

Going to pick up some Rust Bullet and some EastWood Rust Encapsulator for some developing rust on my underbody in hard to reach places, but how bad does my TJ look to all of you rust veterans?

I'm also really worried about taking my belly pan off to get to that part of the frame... what's the protocol if those bolts wont go back in?






That's from the inside of the frame...








Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 02:52 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC